The Manual Forecast display (see below) in the Operator Client allows for the running of single or a manually scheduled forecast.
The Manual Forecast display (see below) in a Standalone system is slightly different from the one in the Operator Client and allows for running of a single forecast or a batch of forecasts.
A single or a series of forecasts can be submitted to the system by pressing [Run]. With [Close], a user can leave the Manual Forecast display.
The various items in the Manual Forecast display are described below.
A workflow can be selected from a drop-down list with pre-configured workflows. By pressing [INFO], a description of the selected workflow can be displayed.
An automatic notification pops up after the completion of the workflow.
A What-if Scenario can be selected from a drop-down list with predefined What-if Scenarios. By pressing [INFO] a description of the selected What-if Scenario can be displayed. What-if Scenarios are defined via the What-if Scenario display.
A forecast description can be entered in this field. Entering of a description is not obligatory.
Please note that the forecast name is generated automatically by the system and consists of the 
start time of a forecast, (ii) the selected workflow and (iii) the selected What-if Scenario.
Scheduler options (only in Operator Client)
Two types of manual forecasts can be defined:
A single forecast will only run once. For single forecast only the T0 of the forecast has to be entered in the date & time field (yyyy-MM-dd HH:mm).
A scheduled manual forecast will run for a period of time and with a time interval both defined by the user. In case a manual forecast is scheduled, the following information should be entered by the user:
In case for example scheduled manual forecasts should always be made at 8:00 AM but the forecast itself should start at 12:00 PM the previous day, the Shift T0 should be set at 8 hours while the Start time is set at 08:00.
Two types of manual forecasts can be defined:
A single forecast will only run once. For single forecast only the T0 of the forecast has to be entered in the date & time field (yyyy-MM-dd HH:mm).
In batch mode, a scheduled manual forecast will run for a period of time and with a time interval both defined by the user. In case a manual forecast is run in batch mode, the following information should be entered by the user:
All runs will be submitted at the same time but will be run with different T0's as defined by the user.
Ticking the approve box will set the status of the forecast automatically to current after it has been completed. In case you want to cancel this action or suspend it, please use the Scheduled Forecast tab in the System Monitor. When using the default synchprofiles.xml, non-approved runs will not be automatically downloaded by the synchronising OC and need to be downloaded manually before they can be opened.
The check box is enabled when the selected workflow has an option allowSelection=true in WorkflowDescriptors.xml. The workflow will be then run only for locations selected in the Explorer Filters. It is not allowed to configure a forecast workflow with the allowSelection option set to true
Specify for which ensemble member indices the workflow should run. Separated by comma use - for ranges. For example 1,5-7,11
The ensemble member selection will apply to ANY ensemble that is present in the workflow.
Not setting a selection results in the full ensemble to be ran.
The user will need to know if the selection given is plausible: FEWS will not check if the specified ensemble members indeed exist.
Leaving Select initial state unchecked, the default state- as has been configured by the system manager- will be used to start the historic run preceding a forecast simulation (see also Running Modules ). For statefull simulation models- like hydrodynamic models- this means that the state selection for a model will follow the state selection rules as configured in the General Adapter Module Instances.
Checking Select initial state allows the user to select a particular state to start the historic run. A selection can be made between a cold and a warm state. A Cold state is a fixed module state defined in the system configuration. Normally various cold states will be available representing characteristic catchment conditions (e.g. dry, normal and wet). When a cold state should be used at the start of the historic run, the following information is required:
A Warm state is a module state that has been generated in a previous forecasting run and stored in the Central Database. In order to find a suitable warm state to start the historic run, a time interval needs to be defined within which the system will look for a warm state. The time interval is defined relative to the T0 of the forecast by the using the following entry fields:
Please note that in case a Warm state is selected as the initial state, the date/time stamp of the warm state found within the defined Search interval will determine the actual start and therefore length of the historic run.
In case no Warm state can be found within the defined Search interval , the system will automatically run as if Select initial state was unchecked. This means that in that case the default state will be used for starting the historic run.
The user can give a forecast run either a High or a Normal priority. The Master Controller will give precedence to high priority tasks above normal priority tasks.
Please note that setting the priority to 'high' does not mean that the task will be directly carried out. In case other high priority tasks are waiting for execution, the new task will be added to the queue. When another task with normal priority is already being executed, it will not be cancelled when a new high priority task is submitted, but will be completed first.
A default forecast length is configured when setting up the forecasting system. Please note that within an area different forecasts lengths may have been configured depending on for example the hydrological (sub-) system and/or the forecasting models used.
"Select modules to include in next run Ctrl+R" : since 2020.01 a workflow can be run for the selected modules also on FSS.