Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Migrated to Confluence 4.0
Wiki Markup
{import:NavigationMenu}

h1. 

Group

...

4:

...

Benchmarks

...

generated

...

by

...

the

...

program

...

itself

...

This

...

section

...

contains

...

tests

...

for

...

which

...

the

...

reference

...

results

...

are

...

generated

...

with

...

D-FLOW

...

SLIDE

...

.

...

4.1

...

Test

...

on

...

the

...

level

...

indicator

...

Description

To check that the level indicator is correctly inputted in D-FLOW

...

SLIDE

...

,

...

the

...

results

...

of

...

the

...

two

...

following

...

calculations

...

should

...

lead

...

to

...

the

...

same

...

results:

...

  • Benchmark

...

  • 4-1a

...

  • uses

...

  • the

...

  • same

...

  • input

...

  • as

...

  • benchmark

...

  • 1-1a,

...

  • refer

...

  • to

...

  • paragraph

...

  • 1.1

...

  • in

...

...

...

  • .

...

  • Benchmark

...

  • 4-1b

...

  • uses

...

  • the

...

  • same

...

  • input

...

  • as

...

  • benchmark

...

  • 4-1a

...

  • except

...

  • that

...

  • the

...

  • Z-coordinates

...

  • of

...

  • the

...

  • geometry

...

  • are

...

  • shifted

...

  • by

...

  • -20

...

  • m

...

  • so

...

  • that

...

  • all

...

  • points

...

  • have

...

  • a

...

  • negative

...

  • Z-coordinate.

...

D-FLOW

...

SLIDE

...

results

4.2

...

Test

...

on

...

the

...

units

...

Description

In the Units tab of D-FLOW

...

SLIDE

...

,

...

it

...

is

...

possible

...

to

...

specify

...

the

...

unit

...

of

...

different

...

parameters:

...

  • Fraction:

...

  • -,

...

  • %,

...

  • o/

...

  • oo or

...

  • ppm

...

  • Length:

...

  • m,

...

  • mm,

...

  • cm,

...

  • inch,

...

  • ft

...

  • or

...

  • km

...

  • Tiny

...

  • length:

...

  • xxxm

...

  • Angle:

...

  • deg,

...

  • rad,

...

  • grad,

...

  • tan

...

  • or

...

  • cot

...

  • Weigth:

...

  • kN/m

...

  • 3,

...

  • N/m

...

  • 3,

...

  • lb/in

...

  • 3,

...

  • MN/m

...

  • 3,

...

  • lb/ft

...

  • 3
  • Pressure:

...

  • kN/m

...

  • 2,

...

  • N/m

...

  • 2,

...

  • Pa,

...

  • kPa,

...

  • MPa,

...

  • kN/cm

...

  • 2,

...

  • psi

...

  • Permeability:

...

  • m/s,

...

  • m/min,

...

  • m/hr,

...

  • m/day

...

To

...

test

...

the

...

correctness

...

of

...

the

...

convertion

...

,

...

7

...

benchmarks

...

are

...

created

...

using

...

the

...

following

...

set

...

of

...

units:

...

Benchmark

...

name

...

Fraction

...

unit

...

Length

...

unit

...

Tiny

...

length

...

unit

...

Angle

...

unit

...

Weigth

...

unit

...

Pressure

...

unit

...

Permeability

...

unit

bm4-2a

...

    m

    xxxm

    deg

    kN/m3

    kN/m2

    m/s

    bm4-2b

    %

    mm

    xxxm

    rad

    N/m3

    N/m2

    m/min

    bm4-2c

    o/oo

    cm

    xxxm

    grad

    lb/in3

    Pa

    m/hr

    bm4-2d

    ppm

    inch

    xxxm

    tan

    MN/m3

    kPa

    m/day

    bm4-2e

      ft

      xxxm

      cot

      lb/ft3

      MPa

      m/s

      bm4-2f

        km

        xxxm

        deg

        kN/m3

        kN/cm2

        m/s

        bm4-2g

          m

          xxxm

          deg

          kN/m3

          psi

          m/s