Versions Compared

Old Version 38

changes.mady.by.user Camiel van Breugel

Saved on

compared with

New Version 39

changes.mady.by.user Camiel van Breugel

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

This WiKi page briefly describes the Delft3D model adapter for Delft-FEWS. This model adapter presently supports the following modules from the Delft3D suite:

...

The configuration file consists of three sections, general, pre-adapter and post-adapter. For example:

Code Block
xml
xml
 <delft3dModel xmlns="http://www.wldelft.nl/fews" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.wldelft.nl/fews http://fews.wldelft.nl/schemas/version1.0/delft3dModel.xsd">
 <description>DCSMV5 FLOW</description>
 <general>
    <module>FLOW</module>
    <runId>dcsm98</runId>
    <workDir>workDir</workDir>
    <modelDir>Repo_dcsmv5</modelDir>
    <auxiliaryGridFile>1953.grd</auxiliaryGridFile>
    <fieldFileFormat>new</fieldFileFormat>
    <outputTimeSeriesInOneFile>true</outputTimeSeriesInOneFile>
 </general>
 <preAdapter>
    <steeringTimeSeriesName>H.profile/dcsmv5</steeringTimeSeriesName>
 </preAdapter>
 <postAdapter>
    <timeSeriesOutput>
       <timeSeries parameter="water level" location="ABDN" layer="1" fewsParameter="H.simulated" fewsLocation="aberdeen"/>
       <timeSeries parameter="water level" location="AUKFPFM" layer="1" fewsParameter="H.simulated" fewsLocation="aukfield_platform"/>
       <timeSeries parameter="water level" location="DELFZL" layer="1" fewsParameter="H.simulated" fewsLocation="delfzijl"/>
       <timeSeries parameter="water level" location="DENHDR" layer="1" fewsParameter="H.simulated" fewsLocation="den_helder"/>
    </timeSeriesOutput>
    <mapOutput>
       <map parameter="water level" layer="1" fewsParameter="H.simulated" fewsLocation="dcsmv5"/>
    </mapOutput>
 </postAdapter>
</delft3dModel>

...

Delft3D-FLOW (example):

Code Block
xml
xml
<timeSeries parameter="water level" location="ABDN" layer="1" fewsParameter="H.simulated" fewsLocation="aberdeen"/>
<timeSeries parameter="dpt. aver. cur. mag" location="STN.1" layer="1" fewsParameter="C.speed.simulated" fewsLocation="UP.STN.1"/>
<timeSeries parameter="Temperature" location="STN.1" layer="19" fewsParameter="T.simulated" fewsLocation="UP.STN.1.L19"/>
<map parameter="dpt. aver. cur. v" layer="1" fewsParameter="V.simulated.u" fewsLocation="Delft3DFLOW_UP"/>
<map parameter="dpt. aver. cur. u" layer="1" fewsParameter="V.simulated.v" fewsLocation="Delft3DFLOW_UP"/>
<map parameter="Temperature" layer="19" fewsParameter="T.simulated.L19" fewsLocation="Delft3DFLOW_UP.L19"/>
<map parameter="Temperature" layer="18" fewsParameter="T.simulated.L18" fewsLocation="Delft3DFLOW_UP.L18"/>

Delft3D-WAQ (example):

Code Block
xml
xml
<timeSeries parameter="APHANIZO" location="Stn_1 (1)" layer="1" fewsParameter="APHANIZO.simulated" fewsLocation="UP.STN.1.L1.WQ"/>
<timeSeries parameter="Chlfa" location="Stn_1 (1)" layer="1" fewsParameter="Chlorophyll.simulated" fewsLocation="UP.STN.1.L1.WQ"/>
<timeSeries parameter="EColi" location="Stn_1 (1)" layer="1" fewsParameter="E Coli.simulated" fewsLocation="UP.STN.1.L1.WQ"/>
<timeSeries parameter="EnCoc" location="Stn_5 (1)" layer="1" fewsParameter="Entero.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="FColi" location="Stn_5 (1)" layer="1" fewsParameter="F Coli.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="FDIATOMS" location="Stn_5 (1)" layer="1" fewsParameter="FDIATOMS.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="GREENS" location="Stn_5 (1)" layer="1" fewsParameter="Greens.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="IM1" location="Stn_5 (1)" layer="1" fewsParameter="IM1.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="IM2" location="Stn_5 (1)" layer="1" fewsParameter="IM2.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="MICROCYS" location="Stn_5 (1)" layer="1" fewsParameter="MICROCYS.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="NH3" location="Stn_5 (1)" layer="1" fewsParameter="NH3.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="NH4" location="Stn_5 (1)" layer="1" fewsParameter="NH4.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="NO3" location="Stn_5 (1)" layer="1" fewsParameter="NO3.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="OSCILAT" location="Stn_5 (1)" layer="1" fewsParameter="OSCILAT.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="OXY" location="Stn_5 (1)" layer="1" fewsParameter="OXY.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="PO4" location="Stn_5 (1)" layer="1" fewsParameter="PO4.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="POC" location="Stn_5 (1)" layer="1" fewsParameter="POC.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="Phyt" location="Stn_5 (1)" layer="1" fewsParameter="Phyt.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="SO4" location="Stn_5 (1)" layer="1" fewsParameter="SO4.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="SS" location="Stn_5 (1)" layer="1" fewsParameter="SS.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="SUD" location="Stn_5 (1)" layer="1" fewsParameter="SUD.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="Salinity" location="Stn_5 (1)" layer="1" fewsParameter="Salinity.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="SecchiDept" location="Stn_5 (1)" layer="1" fewsParameter="SecchiDept.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="Si" location="Stn_5 (1)" layer="1" fewsParameter="Si.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="TOC" location="Stn_5 (1)" layer="1" fewsParameter="TOC.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="Temp" location="Stn_5 (1)" layer="1" fewsParameter="T.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="TotN" location="Stn_5 (1)" layer="1" fewsParameter="TNitrogen.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="TotP" location="Stn_5 (1)" layer="1" fewsParameter="TPhosphate.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="TotalDepth" location="Stn_5 (1)" layer="1" fewsParameter="TotalDepth.simulated" fewsLocation="UP.STN.5.L1.WQ"/>
<timeSeries parameter="pH" location="Stn_5 (1)" layer="1" fewsParameter="PH.simulated" fewsLocation="UP.STN.5.L1.WQ"/>

Delft3D-WAVE (example):

Code Block
xml
xml
<map parameter="Mean wave direction" layer="1" fewsParameter="Wave.direction.mean.ext" fewsLocation="Guanabara.wave.ext"/>
<map parameter="Mean wave period" layer="1" fewsParameter="Wave.period.mean.ext" fewsLocation="Guanabara.wave.ext"/>
<map parameter="Peak wave direction" layer="1" fewsParameter="Wave.direction.peak.ext" fewsLocation="Guanabara.wave.ext"/>
<map parameter="Peak wave period" layer="1" fewsParameter="Wave.period.peak.ext" fewsLocation="Guanabara.wave.ext"/>
<map parameter="Sign.wave height" layer="1" fewsParameter="Wave.sign.height.ext" fewsLocation="Guanabara.wave.ext"/>

...

The Delft3D model adapter and executable can be executed from FEWS in the following way:

Code Block
xml
xml
 <executeActivities>
    <executeActivity>
       <description>Delft3D Adapter</description>
       <command>
          <className>nl.wldelft.fews.adapter.delft3d.Delft3DPreAdapter</className>
       </command>
       <arguments>
          <argument>%ROOT_DIR%</argument>
          <argument><adapter configuration file></argument>
       </arguments>
       <timeOut>10800000</timeOut>
       <overrulingDiagnosticFile>%ROOT_DIR%\diagnostics\delft3dpreadapter.xml</overrulingDiagnosticFile>
    </executeActivity>
    <executeActivity>
       <description>Run delftflow</description>
       <command>
          <executable>bin/deltares_hydro.exe</executable>
       </command>
       <arguments>
          <argument>config-flow2d3d.ini</argument>
       </arguments>
       <timeOut>90000000</timeOut>
       <overrulingDiagnosticFile>%ROOT_DIR%/dcsmv5_Diagnostic_Placeholder.xml</overrulingDiagnosticFile>
    </executeActivity>
    <executeActivity>
       <description>Delft3D Adapter</description>
       <command>
          <className>nl.wldelft.fews.adapter.delft3d.Delft3DPostAdapter</className>
       </command>
       <arguments>
          <argument>%ROOT_DIR%</argument>
          <argument><adapter configuration file></argument>
       </arguments>
       <timeOut>10800000</timeOut>
       <overrulingDiagnosticFile>%ROOT_DIR%\diagnostics\delft3dpostadapter.xml</overrulingDiagnosticFile>
    </executeActivity>
</executeActivities>

...

The below configuration shows an example of the exportStateActivity to export a Delft3D model state from the FEWS generalAdapter.

Code Block
xml
xml
<exportStateActivity>
   <moduleInstanceId>DCSM_Historical</moduleInstanceId>
   <stateExportDir>%ROOT_DIR%/stateInput</stateExportDir>
   <stateConfigFile>%ROOT_DIR%/stateInput/export_states.xml</stateConfigFile>
   <stateLocations type="file">
      <stateLocation>
         <readLocation>dcsm98.res</readLocation>
         <writeLocation>dcsm98.res</writeLocation>
      </stateLocation>
   </stateLocations>
   <stateSelection>
      <warmState>
         <stateSearchPeriod unit="hour" start="-48" end="-1"/>
      </warmState>
   </stateSelection>
</exportStateActivity>

...