This page describes how an existing configuration can be extended to accommodate output displays of the DRA and/or the RIV package.
Pre-condition:
Use MFma_support.exe the Modflow Module Adapter version from 16-09-2008 or later (1,970,290 byte if compiled with GNU95): Check the attachments on http://public.deltares.nl/display/NGMS/Step+4.++Setup+ModuleDataSets+and+Module+Adapter
Use Diagnostic_Search_Strings.dat dated 18-10-2008 (2,819 byte)
Step 1
...
. Preparation
- Replace MFma_support.exe in c:\ngms\<region>\modules\bin\mf
...
- Replace Diagnostic_Search_Strings.dat in c:\ngms\<region>\modules\<model>\Mf<vkd>
Step 2. Update locations and grid specification
While the output of the RIV and DRA package can be produced as a grid covering the full model area, it is recommended to create a sparse grid (similar to the StreamCells-sparse grid), to save disk space. The Module Adapter contains functionality to accommodate the generation of such sparse grid. Once generated, this sparse grid needs to be copied to the main grids.xml file. In addition, the locations.xml file needs to hold a location-id which points to this grid.
Step 2.1 Update grids.xml
- extend module Adapter instructions for config preparation (XXX_prepare.in) by adding the following command(s):
- RIV_OUT QRIV (creates a sparse grid of river cells)
- DRN_OUT QDRA (creates a sparse grid of drainage cells)
- GHB_OUT Q_GHB (creates a sparse grid of boundary cells)
- for each of the generated grids.xml:
- copy the irregular grid-definition into the main grids.xml
- rename the locationId into "<model>_DrainageCells_sparse_grid", resp. "<model>_RiverCells_sparse_grid", resp."<model>_BoundaryCells_sparse_grid".
- replace the number of rows by 1
- replace the number of columns by the number of grid-cells
|
|
Step 2.2 Update locations.xml
- Add locationId for each new sparse grid
Info |
---|
Example |
Step 3. Update/verify the parameters list in the IdMap-files
- Add parameter mapping for each idMap-file (except import_observerd)
<parameter external="QDRA" internal="QDRA.xxxx"></parameter>
where xxx refers to the scenario type (hist, nat, recact, fullic, lta, fullicS, whatif) - Save file with a new version number
Step 4. Update Module Adapter output Instructions file (XXX_output.in)
- For each scenario, extend BINARY MAPSTACKS MERGE command with QDRA and QRIV
Info Example
BINARY_MAPSTACKS MERGE H, QX, QY, QZ, QSTR, QSTR_ACCU, QSTOR, Q_GHB, Q_HBND,
Step 5. Update Module Instances
- Open the ModuleInstances spreadsheet for this model as well as the generator-spreadsheet with the macro's
Step 5.1. Update General Adapter import activities
- add importMapstacksActivity for QDRA, QRIV using <model>_merged as a temporary time series (synchLevel 9, expires in 16 hour)
Info | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
Example row in spreadsheet:
|
Step 5.2. For each scenario conduct the following steps:
Step 3) Update Module Adapter Instructions file
Step 4) Update General Adapter import activities
Step 5) Add interpolation from full model grid to sparse river/drainage cells grid
- add interpolation for QDRA, QRIV, Q_GHB, Q_HBND using <model>_xxxCells_sparse_grid as output
Info | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Example row in spreadsheet
|
Step 6) 5.3. Update compare between scenarios
- add compare for QDRA, QRIV and Q_GHB, Q_HBND using <model>_xxxCells_sparse_grid as output
Info |
---|
...
Example row in spreadsheet
|
Step 5.4. Regenerate new Module instances
- run the macro's
- update file version before copying into the Config-directory
Step 6. Update displays
Typically, only an update of the GridDisplay will be needed.
Update grid display
- Copy the row-set holding the display specification for Recharge
- Paste after the last input parameter
- Replace all references to recharge by the references to Drainage or River properties
- Folder name
- Parameter
- LocationId
Info | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Example row in spreadsheet
|