| scrollbar |
|---|
| Table of Contents |
|---|
Components of spatial display
Spatial Display
The Spatial Display grid display can be used to display show time series of any typekind: scalar, polygon, or grid (see the figures below for examples). The display will depict the data is shown on a map background. The time on the display time is then set using a ruler that can be moved manually by hand or made set to move automaticallyon its own.
The spatial display
...
is made up of the following
...
parts:
- A spatial, grid, or map display with layers that you can change
- A
- Spatial Display selection filters
- Control Toolbar with following general options for:
- Manual zoom and zoom previous buttons
- Predefined zoom range selector
- Zooming in and out and moving around
- Turning map layers or metadata on and off, like labels, values, flags, thresholds, etc.
- A Time Slider Toolbar with general options (found at the bottom of the map since 2019.02):
- Buttons for play
- , pause, stop, step forward, step backward, and record
- A time slider with a time slice indicator
- An indicator for data availability and maximum value
- Moving average slider
- Legend
- Contours button
- Export time step data in ascii grid-file
Grid display selection filters
The selection filters show which displays have been configured. Select a filter to display the data. Note that each grid display may be configured differently, i.e. with a different period of data to be displayed, with a different background map, etc. The configuration allows filters to be highlighted in bold.
Control Toolbar
The toolbar provides the controls for displaying the spatial information via through the following buttons:
- (the colors match the legend)
- Filters for selecting what to show in the Spatial Display (you can set up plots ahead of time)
- A table or bar legend (you can choose to accumulate data)
- Options for exporting or recording data and time series
Control Toolbar
The toolbar offers controls for presenting the spatial information through various buttons. The functionality of zoom options and layers is detailed in the FEWS Explorer section. (see chapter 2).
Button | Description |
|---|---|
| Contours. You can turn contour lines on or off. Numbers show up when the animation is stopped or paused. The colors, which show the value, stay visible. A bilinear interpolation is used to make the grid smooth. This is necessary for calculating the contours. Even when the labels and contour lines are turned off, the smooth grid can still be seen. The bilinear interpolation is only used on the cells of the grid that are rectangular and aren’t rotated too much compared to the screen orientation. |
| Grid lines. Toggles grid or polygon lines on or off |
| Product Info. Toggles product info on or off. (only shown if there are products present in the configuration, see the page on the Forecast Product Information Panel) |
| Labels. You can toggle labels on or off. The drop-down options include turning locations, values, and/or units in the labels on or off, and increasing or decreasing the number of decimals shown in the labels and tooltips. Since FEWS 2022.02, this also works for grids, but only when you zoom in until there are fewer than 20,000 grid cells displayed and one of the cells is larger than 10 pixels. |
| Value to local reference level. |
| Flags. Switches to flags for selected time series / gridplot (quality, modifiers or thresholds) |
| Search and select forecasts. Switches to (previous) forecasts. |
| Show spatial thumbnails. Toggles thumbnails of each time step below the main spatial display on or off. |
| Show spatial ensemble thumbnails. Displays the ensemble thumbnails panel. |
| Sketch mode buttons and other sketch drawing options. Switches the sketch mode between drawing points, adding points, drawing longitudinal profiles and drawing areas when the map is clicked. Contains additional options to save/load sketches and delete the current sketch. |
| Options to show a graph based on current sketch. Drop-down menu with options to extract scalar time series, vertical profiles, longitudinal profiles, 2D longitudinal profiles, calculate budget and calculating the mean max min time series (for sketched areas). |
| Activate spatial modifier mode. Toggles spatial modifier mode on or off (only shown if at least one spatial modifier is configured in ModifierTypes.xml). The additional modifier mode buttons shown when modifier mode is toggled on are explained in the spatial modifier section. |
| Display time. Choose display time (period) |
| Attributes. |
Time Slider Toolbar
The time slider and its buttons have been moved to a separate toolbar located at the bottom of the spatial display.
| Preload. The preload button allows the grids for all time steps to be downloaded in the background. This ensures a smooth animation without pauses. The progress of the download is indicated by a green line on the time slider. |
|
Button
Description
Play. Starts continuous play mode. The slider will indicate the time slice being shown. |
This button is merged with the pause button. So after this button is pressed, the pause button appears. | |
| Pause. Stops continuous play mode. The time slider remains at the time displayed at the moment. |
Stop . Stops continuous play mode. The time reverts back to the start time..
This button appears if the play button is previously pressed and the continuous play mode is running. | |
| One frame back |
. Moves the time slider back one timestep. |
| One frame forward |
. Moves the time slider forwards one timestep. | |
| Record. |
This function creates a movie file |
in AVI or animated GIF format. By default, the AVI format is used unless the filename ends with ‘.gif’. Once the file is opened, the display will start playing from the current time position |
and will continue until the stop button is clicked. |
| Time |
| Slider | The time slider can be dragged to specific time slice. |
Data availability | The data availability indicator |
gives a visual |
hint about where data can be found. When data is available, the |
color of the data availability indicator will |
match the |
highest value found in the data for that time slice.
|
...
|
Selection filters
The selection filters indicate which displays have been set up. You can select a filter to show the data. Keep in mind that each grid display might be set up differently, for example, they might show data from different periods, use different background maps, and so on. The configuration allows certain filters to be highlighted in bold.
Locations attribute filter
With the location attribute filters, you can hide one or more locations/grids in the plot. The button ( 
) is only visible when attributes are configured for the plot.
Legend
The legend can be displayed as a table or a bar. It identifies the color associated with each range of values. You can rescale the range of values for each color by right-clicking on the display and choosing ‘Rescale Classification’ from the pop-up menu. The display colors will then be updated to match the new classification. After rescaling, the lowest and highest values in the legend will match the minimum and maximum values of the data in the current zoom extent of the display (for the selected time slice). If you zoom in on an area where all data points or grid cells have similar colors, you can use rescaling to better see the differences in data values. To go back to the default classification, right-click on the display and choose ‘Back To Default Classification’ from the pop-up menu. When you select a different plot, the classification always reverts back to the default for that plot.
Users can change the classification colors by double-clicking the colored squares in the table legend. These changes are saved in the user settings. If a user has made changes, they can discard them by right-clicking the display and selecting ‘Discard User-Defined Classification Colors’.
When multiple classifications are set up, users can select a classification from the drop-down menu located directly above the table legend.
A bar legend displays fluent scale bar as shown in the picture below:
Moving Average or Accumulation Slider
The moving average slider can be
...
set up to
...
let the user
...
choose from a number of moving average settings. Each moving average window is then recalculated for
...
the whole period.
When you close the program, both the selected grid plot and the chosen aggregation time step are saved in the user settings. When you reopen FEWS, the same aggregation time step will be selected. If you’ve selected an aggregation time step and then switch between different plots, FEWS will try to select the same time step again for the new plot. In the image below, the Moving Accumulation Slider is set to 1 day.
Since the 2023.02 the accumulation slider automatically contains an extra tick at the end of the slider do accumulate the time steps to/from the display time
Last Value Checkbox
When this checkbox is selected, it displays the last available time series configured in the grid plot. This can be handy when there are multiple time series with different or non-equidistant time steps defined within one grid plot, and a time is selected where one time series doesn’t have a time step. The time series can be either scalar or grid. For scalars, the last time step (that is still within the visible period) without a missing value is shown. For grids, just the last time step is shown, even if it might be a missing value. The checkbox will only appear when neither an accumulation nor a moving average slider has been configured, and it can be hidden through configuration.
Selecting different forecasts
Selecting different forecast times
A “search and select forecast” (
) button is available. This button becomes active if more than one forecast is available, meaning there are multiple forecast time series with different forecast times in the database and the <numberOfRecentForecasts> is set to more than 1 for the selected grid plot. Clicking the button allows you to cycle through the available forecasts. The drop-down menu will display the forecast times of the available forecasts, and selecting one of these times will change the displayed forecast to the one selected.
Alternatively, you can use the spatial thumbnails to select different forecasts (and different time steps). The spatial thumbnails panel will display one row for each available forecast. You can toggle this panel on or off using the button (
).
Selecting different ensemble members
The button (
) can be used to open the spatial ensemble thumbnails panel.
The spatial ensemble thumbnails window will open, displaying a thumbnail for each individual ensemble member at the selected time.
In this window, users can choose the ensemble thumbnail they want to view. This selected ensemble member will then be visualized in the grid display.
The ensemble member is identified at the bottom of the thumbnail and in the bottom right corner of the grid display.
The thumbnails can be resized at the bottom right corner of the first thumbnail. A resize mouse cursor will appear when hovering over that corner.
The size will be stored in the user settings for future use.
Contours
The contour button generates contours in real-time for the grids being displayed. Since 2021.01, it’s also possible to show contours for irregular grids and across multiple grids displayed simultaneously. When the contour button is pressed, bilinear interpolation is used to calculate a value for each pixel individually. The grid display knows the grid cell for every pixel at the current map extent and zoom level. The detection of neighboring cells is done at the screen pixel level and works for existing configurations. The interpolation is automatically turned off for individual cells that are not rectangular or are rotated more than 10 degrees compared to the screen. The contours are calculated for the interpolated pixel values for the current zoom extent. The contour button is disabled for point data and when contours are configured for a different parameter on top of the parameter that is using the colors from the legend.
Extracting data from the Spatial Display
| Info | ||
|---|---|---|
| ||
In 2019.02 the options to extract data from the spatial display were moved from the right-click menu of the map to the drop-down menu of a new ( |
Export time step data in
Legend
The legend identifies the colour used for each range of values.
Contours button
To turn on/off contour lines (regular grids configured with contour lines only). Numbers appear when the animation has stopped or paused. The colors, which indicate the value remain visible.
...
ascii grid-file
By right clicking on the display, the grid data for a specific timestep can be exported in an ascii file. Select the desirable time step with the control toolbar.
Extracting scalar time series from grid
...
You can extract scalar time series
...
from the grid by double-clicking on the point of interest. Depending on the type of data
...
displayed, the scalar time series will
...
correspond to
...
a point, polygon, or grid cell. Here’s another way to do it:
- First, select the point of interest by left-clicking. A colored dot will appear to mark the selected point. For grid data, an additional green dot will be drawn to indicate the center of the selected grid cell (you may need to zoom in to see the green dot if it overlaps with the colored dot).
- Extract the time series
...
- for the selected point either by selecting ‘Show Time Series’ from the drop-down menu of the (
)button or by using the Ctrl+F3 shortcut.
Instead of immediately extracting the time series and showing a time series dialog, you can use the “Copy Time Series” option to copy the time series for the selected point to the FEWS clipboard. Copied time series can then be pasted into a time series dialog later using the paste button in its toolbar.
You can draw several points by selecting the “Add Point” sketch mode through the sketch mode button (
) or by holding the left ctrl and shift buttons while left-clicking on the points of interest. When several points have been drawn, the “Show Time Series” and “Copy Time Series” options will show or copy separate time series for each of the drawn points.
Instead of manually drawing a point or points, you can use the ‘Show Time Series For Coordinates…’ option in the drop-down menu of the () button. This will open a small dialog prompting you to enter the coordinates of the point you wish to use.
A series extracted from a grid
...
is not related to a known location or polygon ID. The series will
...
be identified using the grid coordinates.
...
...
The graph will automatically pop up with the time series of the selected point, polygon, or grid cell. When animating the grid display, a marker will move over the time series graph as well.
...
To extract a different scalar time series, double-click on another point of interest. This will draw a new dot and extract a scalar time series for that point. Please note that when extracting a scalar time series from a data point in the display, the dot drawn on top of the data point has a different color from the point itself. This might make it look like the data point has a different color because of the dot. The dot can be erased by selecting ‘Delete Points’ in the drop-down menu of the sketch mode button (or using the keyboard shortcut Ctrl+Delete).
Note:
It’s important to stop the grid movie before
...
creating a time series graph
...
. Running both at the same time can slow down the system
...
due to the heavy processing load from executing multiple processes simultaneously.
The extraction of scalar time series is not available for rotated pole geodatum types. In some cases, the extraction of scalar time series may behave unexpectedly near the North Pole or South Pole.
Extracting scalar time series for each ensemble member at one from grid
Since the 2020.01 version, it’s possible to display the scalar time series for each ensemble member for a single grid cell.
Extracting vertical profiles from 3D data
When the spatial display is presenting 3D (layered) data, you can extract a vertical profile. Here’s how:
- Draw a point as described in the previous section.
- Then, select the ‘Show Vertical Profile’ option in the drop-down menu of the button or press Ctrl+F4. This will open a time series dialog with the vertical profile for the drawn point.
Alternatively, you can use the ‘Show Vertical Profile For Coordinates…’ option in the drop-down menu or press Ctrl+Shift+F4.
You can also create a vertical profile with a color map:
- Select the ‘Use Color Map’ option in the drop-down menu of the button or use Ctrl-M.
- The vertical profile will then be displayed as a graph of a parameter over time, with the colors in the plot indicating the values of the selected parameter.
Extracting longitudinal profiles (Xsections) from a grid time series
Longitudinal profiles time series can be extracted from the grid data and shown in a separate graph as well. The profile (or cross section) is defined by drawing a profile sketch. Start drawing a profile sketch either by opening the drop-down menu of the sketch mode button and selecting 'Draw Longitudinal Profile' or by Ctrl+left clicking on the desired start point for the profile. A colored dot will be drawn to indicate the selected start point. Add additional line segments to the profile by left clicking in the display. Finish drawing by double-clicking on the desired end point for the profile. Green dots along the profile indicate which grid cells are used for the profile.
Once a profile sketch has been drawn, extract the profile either by selecting 'Show Longitudinal Profile' from the drop-down menu of the 
button or by using the Ctrl+F2 shortcut. The graph of the profile will show automatically.
Instead of drawing the profile on the map, the 'Show Longitudinal Profile For Coordinates...' option can be used to enter coordinates for the profile points.
To extract a different profile just start drawing another profile. This will erase the previous sketch. The profile sketch can also be erased by selecting 'Delete Sketch' from the right-click drop-down menu.
When animating the grid, the profile follows the same animation. When animating the profile only, the grid animation remains fixed. Note that the same cross section can be reused when switching to another plot (Ctrl+F2 will open a new window).
Note:
Even more essential then for scalars, it is wise to pause the grid animation when dragging a cross section to be shown.
The cross section is defined by following the right mouse menu or by: Ctrl+right mouse - drag - release mouse. The profile will show automatically.
Note:
Extraction of longitudinal profiles is not available for irregular grids, points and polygons. The profile sketch will be erased when switching to a plot that contains data of one of these types. Extraction of longitudinal profiles is also not available for rotated pole geodatum types. In some cases extraction of longitudinal profiles can exhibit unexpected behaviour for profiles crossing the dateline or located near the North Pole or South Pole.
Note:
If longitudinal profile data is displayed in the spatial display, then there is no need to draw a profile sketch. Just press the F2 key or right click and select 'Show Profile' from the pop-up menu to show the graph of the profile. 
Create 2D longitudinal profiles from data in the Spatial Display
Create a 2D longitudinal profile for 3D data in the spatial display. A longitudinal profile should be drawn as described in the previous section. Open up the 2D longitudinal profile in the Time Series Display with Ctrl-F11, or by selecting the 'Show 2D Longitudinal Profile' option in the drop-down menu of the button. There is also a 'Show 2D Longitudinal Profile For Coordinates...' option, to allow entering coordinates of the profile points instead of sketching the profile on the map.
Note, this feature only works for
- data within 1 grid partition. In some cases 3D data model runs are run on multiple domain partitions. This data can be shown as a 2D longitudinal profile, but only if the profile remains within a single domain.
- scalar data (e.g. Water temperature or salinity), and not yet for vector data like currents.
Extracting data for an area from a grid time series (Calculate Budget)
For certain types of data it is possible to extract time series data for a specific part of a grid and show this in a separate graph. This is only possible for scalar data with dimension "discharge" (L3/T), "volume" (L3), "velocity" (L/T), "length" (L) or "amountOfSubstance" and for horizontal flow data with dimension "discharge" (L3/T) or "velocity" (L/T). The dimension of a parameter group can be configured through the parameters.xml and a list of available dimensions can be found at Configuration Guide > Regional Configuration > Parameters.
The specific part of the grid is defined by drawing an area sketch (a closed polygon surrounding the desired area). Start drawing an area sketch either by selecting 'Draw Area' from the drop-down menu of the sketch mode button and then left clicking the map, or by Shift+left clicking on the desired start point for the area. A colored dot will be drawn to indicate the selected point. Add additional line segments along the edge of the desired area by left clicking in the display. Finish drawing by double-clicking. The last point in the sketch will be connected to the first point automatically to create a closed polygon that surrounds the desired area.
Once an area sketch has been drawn, extract the desired data by selecting the 'Calculate Budget' option from the drop-down menu of the button. The corresponding graph will show automatically. The 'Calculate Budget' option will perform one of the following calculations, depending on the type and the dimension of the selected data.
Grids that contain scalar data (e.g. water levels or rainfall data):
- For dimensions "discharge" (L3/T, e.g. flow in m3/s), "volume" (L3 e.g. volume in m3) and "amountOfSubstance"' the calculation will be 'volume summation'. This calculates the sum of the values inside the area. This uses all grid cells that are (partially) inside the area. The value of each grid cell is weighted using the fraction of the grid cell that is inside the area.
- For dimensions "velocity" (L/T, e.g. velocity in m/s) and "length" (L, e.g. water level in m) the calculation will be 'area times average level'. This calculates the average level inside the area multiplied by the size of the area. This uses all grid cells that are (partially) inside the area. The value of each grid cell is weighted using the fraction of the grid cell that is inside the area.
- If another dimension, or no dimension, is configured for the selected data, then the option 'Calculate Budget' is not enabled.
Grids that contain horizontal flow data in the form of u,v vectors:
- For dimension "discharge" (L3/T, e.g. flow in m3/s) the calculation will be 'mass balance horizontal flux'. This calculates the net horizontal flow into/out of the area. This uses all grid cells that are for at least 50% inside the area.
- For dimension "velocity" (L/T, e.g. velocity in m/s) the calculation will be 'mass balance horizontal velocity'. First for each grid cell the value of u, respectively v, is multiplied by the height of the gridcell, respectively the width of the grid cell, to get flow values (The height of the flowing water mass is taken to be 1). Then the net horizontal flow into/out of the area is calculated. This uses all grid cells that are for at least 50% inside the area.
- If another dimension, or no dimension, is configured for the selected data, then the option 'Calculate Budget' is not enabled.
If there is no grid plot configured with a parameter group with one of the dimensions supported by the 'Calculate Budget' option, the option will be hidden.
To extract data for a different area just start drawing another area. This will erase the previous sketch. The area sketch can also be erased by selecting 'Delete Sketch' from the sketch drop-down menu (or pressing the keyboard shortcut "delete").
When animating the grid display, a marker will move over the time series graph as well. Note that the same area sketch can be reused when switching to another plot (right clicking and selecting one of the relevant options will open a new window). 
NoteNote:
Even more essential then for scalars, it is wise to pause the grid animation when dragging a cross section to be shown.
an area for extracting data.
Note:
Extraction of data for an area is not available for quadrilateral grids, irregular grids, polygons and points. Extraction of data for an area is also not available for rotated pole geodatum types. In some cases extraction of data for an area can exhibit unexpected behaviour for areas crossing the dateline or located near the North Pole or South Pole.
Extracting min max and mean time series for an area
Available since 2019.02. An area should be drawn as described in the first paragraph of the previous section. Then select 'Show Min Max Mean Time Series For Area' in the drop-down menu of the button. A Time Series Dialog will show the expected time series.
Extracting data for multiple plots at once (available since build 18645)
It is possible to extract data for multiple plots at once. In the selection filters select a folder that contains more than one plot (as direct children). The first plot in the folder will be displayed. Then extract scalar time series, longitudinal profiles or data for an area in the usual way. The extracted data for all the plots in the selected folder will be shown in a combined diagram, where each plot has a separate graph.
Saving and loading sketches from shape files (available since build 18645)
Once a profile sketch or an area sketch has been drawn, the sketch can be saved as a shape file (*.shp file) by selecting 'Save Sketch As Shape File' in the drop-down menu of the sketch mode button (shortcut: Ctrl+Shift+S). A saved sketch or any other shape file that represents a profile or an area (a closed polygon) can be loaded into the display by selecting 'Load Sketch From Shape File' (shortcut: Ctrl+Shift+S). The loaded sketch can then be used for extracting data. When loading a sketch, the previous sketch will be erased.
Note:
A shape loaded from file will only be used as an area sketch (a closed polygon) if the first and last points of the shape have exactly the same coordinates. Otherwise the shape will be used as a profile sketch.
Creating Spatial Modifiers
In 2019.02 the first spatial modifiers were added. These modifiers are used to modify a grid time series and must be created through the Spatial Display instead of the Modifiers Panel.
Spatial Modifier Mode
To create spatial modifiers, the spatial modifier mode must be activated. To do so, first select the grid plot containing the time series you wish to modify, and then activate spatial modifier mode through the 
button. This button will only be visible if at least one spatial modifier is configured in the modifier types (See Configuration Guide > 04 Regional Configuration > 25 ModifierTypes). The button will only be enabled if the currently selected grid plot contains exactly one time series, for which a spatial modifier type is configured. Thus, this button is only available if it is actually possible to modify the currently visible time series.
To indicate which grid plot is currently being modified, i.e., the grid plot which was selected when modifier mode was activated, a wrench icon will appear in the tree and the tool-tip of the modifier mode button will show the name of the grid plot.
It is only possible to create spatial modifiers for the grid plot on which spatial modifier mode was activated. If you wish to change which plot you are modifying, spatial modifier mode must be deactivated (by clicking the button) and reactivated on the new grid plot.
When spatial modifier mode is activated, the spatial modifier button section will appear in the toolbar. This contains the following buttons.
Button | Description |
|---|---|
| Start time. Select the current time as new modifier start time. |
| End time. Select the current time as new modifier end time. |
| Clear period. Clear the selected new modifier period. |
| Copy modifier. Used when creating spatial copy modifiers. |
| Paste modifier. Used when creating spatial copy modifiers. |
| Spatial profile. Used to create a spatial profile modifier. |
When spatial modifier mode is activated the colors on the time slider will indicate the time periods on which modifiers are applied and the selected period for new modifiers (if any). The new modifier period will be shown in green. The color for the time steps on which a spatial modifier is active can be configured. In this example the configured color is black. It is also possible to configure ticks for the start and end time of the period of applied modifiers and start and end time of the selected new modifier period.
When spatial modifier mode is activated, the Modifiers Panel will show the modifiers for the grid plot being modified, instead of showing the modifiers for the selected forecast tree node. This is indicated by the title appearing directly above the table in the modifiers panel. When spatial modifier mode is deactivated, the modifiers panel will return to showing the modifiers for the selected forecast tree node.
When spatial modifier mode is activated, this is done "globally". This means that on any other spatial displays, spatial modifier mode will be active as well and for the same grid plot.
General Steps
This section explains the general steps necessary to create any spatial modifier. For any spatial modifier, the area on which the modifier is to be applied must be drawn and the time period for which the modifier should be applied must be selected. These steps can be done in any order.
Sketching the spatial modifier area
The area(s) on which a spatial modifier should be applied should be sketched using the sketch functionality of the spatial display. You can start drawing an area by selecting the "Draw Area" tool in the sketch button drop-down menu and left-clicking the map. Alternatively, you can hold the shift-key on the keyboard while left-clicking the map. Once you have started an area, left-clicking will result in a new point being added to the area border. Double clicking will finish the drawing by adding the double clicked point and closing the drawn polygon. Additional areas can then be drawn in a similar fashion. The drawn areas can be removed by using the "Delete Sketch" option in the sketch button drop-down menu or pressing the "Delete" key on the keyboard.
The current sketched areas will appear on the map with solid lines and point markers on each of the sketched border points:
Selecting the new modifier period
Each spatial modifier needs to be created for a certain time period. This period is set by selecting the start and end time of the period. Once a valid period has been selected, it will be marked green on the time slider. The selected start and end time will be marked with ticks if this has been configured.
To select the new modifier period, first select the time step you wish to use as the start or end time. Then the 
and 
buttons can be used to select the current time step as the new modifier period start or end time respectively. Alternatively, the time slider has been given a right-click menu which also contains these options:
The selected new modifier period can be cleared through the 
button or the "Clear the selected new modifier period" option in the right-click menu of the time slider.
Note that all options to select a new modifier period are only available when spatial modifier mode is active. If spatial modifier mode is deactivated, the new modifier period is cleared.
Creating a Spatial Copy Modifier
A spatial copy modifier takes the values of a different grid time series for a certain area and time period, and copies these values over the existing values in the modified time series. To create a spatial copy modifier, spatial modifier mode must be activated and an area and time period must be selected as explained in the sections above.
Select the grid plot you wish to copy the values from and use the 
button to copy a "potential spatial copy modifier" to the clipboard. When the button is clicked, the Spatial Display will take the area sketch, new modifier period and grid plot selected at the time the button is clicked and use this in the new "potential spatial copy modifier".
To actually create a spatial copy modifier the "potential spatial copy modifier" needs to be pasted into the grid plot being modified. To do so, select this grid plot and then click the 
button to paste the most recently copied information. The drop down menu of the button shows information on the most recent copy actions (up to five). Selecting one of the menu items in the drop down menu will paste that "potential spatial copy modifier".
It is possible to open two spatial displays side-by-side to be able to view the grid plot being modified as well as the time series you wish to use to copy values from. Note that to do so, the sketch and time period to be used should be selected in the same spatial display as you will use to select the time series you will copy values from and click the button.
When the paste button (or one of the drop-down menu items) is clicked, the spatial modifier creation dialog will be shown to set the general modifier properties and confirm the creation of the new modifier. The contents of this dialog are explained below.
Creating a Spatial Profile Modifier
A spatial profile modifier is created by defining an area, period and scalar time series with which the values in the grid cells within the area will be replaced. To create a spatial profile modifier, spatial modifier mode must be activated and an area and time period must be selected as explained in the sections above.
Select the "Spatial Profile"-button to make the spatial profile modifier dialog appear. This dialog is used to specify the scalar time series that will be used to replace the grid cell values. The time series can be edited through the table.
When the ok-button is pressed, the spatial modifier creation dialog will appear to set the general modifier properties and confirm the creation of the new modifiers. The contents of this dialog are explained below.
When an existing spatial profile modifier is selected in the modifier panel, the scalar time series can be edited. The selected area and period can not be edited.
Spatial Modifier Creation Dialog
When a spatial modifier is created, for example when the paste button is clicked to create a spatial copy modifier, the spatial modifier creation dialog is shown. This dialog allows the user to set the modifier properties like it's name and priority, and select the valid time they wish to use. In the top part of the dialog, the summary of the modifier that will be created is shown. This summary can't be edited, but it is selectable to allow copying parts of the summary when desired.
When the OK button is pressed, the spatial modifier will be created. A new uncommitted modifier will appear in the modifiers panel and the current sketch in the grid display will be deleted.
Modifier Properties
The modifier properties shown and set in the spatial modifier creation dialog are the same as the modifier properties that would be set through the modifiers panel for non-spatial modifiers. This includes the name, any user-defined description fields and the modifier priority. These properties can later be edited through the modifiers panel by selecting the modifier you wish to edit in the table.
Name
The name of the modifier. This field will be automatically filled with a summary of the modifier as a suggestion. It can contain at most 64 characters.
User Defined Description Fields
These can be configured in the modifier types. In the example shown above, there is one user defined description field configured called "Comment". These description fields can be used to allow users to add some additional information on the modifier they created.
Priority
The priority controls the order in which spatial modifiers are applied. This can be relevant if spatial modifiers have areas that overlap. For example, you may wish to create a spatial modifier for a large area, then modify a smaller subarea in a different way with a second spatial modifier. Modifiers are applied from the one with the highest value for priority to the one with the lowest value (so a modifier with priority 1 will be applied after a modifier with priority 2). This causes the modifier with the lowest value to be "on top". By default the priority is set to 1. In the previous example, you should set the priority of the modifier for the large area to a higher number, so the spatial modifier for the smaller area will appear on top (with default priority of 1). When two spatial modifiers have the same priority, there is no guarantee they will be applied in a certain order.
Validity
The validity options allow setting the forecast(s) a spatial modifier should be applied to. There are two options:
- Only valid for current forecast. If this option is selected, the newly created modifier will only be applied to the current forecast. Its valid time will be set to the forecast time of the current forecast.
- Always valid. If this option is selected, the newly created modifier will be applied to all forecasts (for the same time series). Its valid time will be left blank. This means the modifier will also be applied to previous forecasts and any new forecasts. Note that if the time period of the modifier falls outside the time period of a forecast, naturally applying the modifier will have no effect.
Viewing Existing Spatial Modifiers
When viewing a modified grid time series while spatial modifier mode is not active, the time slider will show colors to indicate the maximum value at a certain time step as usual, but these colors will be replaced by the configured "modifier color" to indicate at which time steps a modifier is applied. When hovering over the time slider on a time step where a modifier is applied, the tool-tip will show the names and any user defined descriptions of the applied modifiers.
When spatial modifier mode is activated, the time slider will no longer show the maximum value colors, but will still mark the periods on which modifiers are active with the "modifier color". When a time step is selected for which modifiers are active, the areas on which these modifiers are active will be shown on the map (with a dashed border). When hovering near the border of one of these areas, a tool-tip with the name and any user defined descriptions of this modifier will be shown and the area on which it is active will be highlighted.
Setting the display time
The display time in the spatial display can be changed in the standalone system only an Operator Client and in a Stand Alone system. The use is similar to the setting the display time in the data display, but with less modification possibilities. When the display time is modified, the relative start and end times of the data to be shown are reset and the time slider is adjusted accordingly.
When pressing the <Save> button in the pop-up, the changes made to the display time are stored in the user_settings.ini. Next time the FEWS system is started these 'non-default' settings will be used. To revert back to the default display period, press the <Reset> button and press <Save> again.
