Wiki Markup |
---|
scrollbar |
Table of Contents |
---|
Please note that for running DFlow-FM from Delft-FEWS only a pre-adapter is needed (a post-adapter is not needed).
...
Class name: nl.deltares.dflowfm.DFlowFMPreAdapter
Properties
model_ |
---|
id | (required) | Identifier of the model. This should be the first part of the .mdu file name. This is used to find the relevant .mdu file(s) and restart .nc file(s), as described below. |
---|---|---|
mdu_file | Deprecated. Do not use. | Pathname of the |
mdu file to update. This should be either an absolute path or a path relative to the workDir specified in the netcdf run file. | |
input_grid_files_to_convert | (optional) |
---|
Deprecated. The latest version of D-Flow FM can directly read grid NetCDF files that are exported from Delft-FEWS. This works for the parameters wind, pressure, rainfall, radiation, temperature and humidity. Therefore converting grid files is not needed anymore. | One or more |
pathnames of netcdf files with input grid data that should be converted. The pathnames should be separated by semi-colons (;). Each pathname should be either an absolute path or a path relative to the workDir specified in the netcdf run file. |
Notes for users
- For all files that are written by this adapter, if the file to be written already exists, then it will be overwritten.
- This program assumes that the model always runs in time zone GMT.
- This program writes log messages to a log file called dflowfm_pre_adapter_log.txt in the workDir specified in the netcdf run file.
- This program The pre-adapter uses the information in the specified netcdf run file as input and uses this information to do the following actions:for its activities (see below).
pre-adapter activities: Update MDU file
...
(s)
In the
...
found mdu file(s) the following entries will be updated automatically (no tags needed):
TStart | Start time of the model run, in units of Tunit relative to RefDate. |
---|
...
|
...
mdu file. | |
TStop | End time of the model run, in units of Tunit relative to RefDate. |
---|
...
|
...
mdu file. | |
RestartFile | Either |
---|
...
* pathname of the input state file relative to the MDU file if the input state file is not empty (warm state start) or |
...
* empty string if the input state file is an empty dummy file of 0 bytes length (cold state start) or |
...
* empty string if there is no input state file at all (cold state start). | |
RestartDateTime | The restart time, this is set equal to the start time of the model run. |
---|---|
RstInterval | Interval (in seconds) for writing *_rst.nc restart files. |
...
RstInterval can be overwritten by a property in the run info file called "restartIntervalForFm" |
MDU file name format
The mdu
...
file(s)
...
Each netcdf file should contain only one variable with grid data. If a netcdf file contains multiple variables with grid data, then an error is given. The extension of the created file depends on the name of the variable in the netcdf file as follows:
netcdf variable name | extension |
---|---|
x_wind | .amu |
y_wind | .amv |
air_pressure | .amp |
any other name | not supported by DFlowFM (for rainfall DFlowFM can use the netcdf file directly) |
...
The format (meteo_on_equidistant_grid/meteo_on_curvilinear_grid) of each of the created files depends on whether there is an auxiliary grid file present for that file. To use an auxiliary grid file for a given netcdf file, it must have the same path and name as the netcdf file, but a different extension (.grd). If an auxiliary grid file is present, then the netcdf file will be converted to a curvi file of type meteo_on_curvilinear_grid that refers to the auxiliary grid file. Otherwise it will be converted to an arcinfo file of type meteo_on_equidistant_grid. For rectangular and curvilinear grids there must always be an auxiliary grid file present, otherwise an error is given. For regular grids no auxiliary grid file is needed.
grid type | auxiliary grid (.grd) file needed | type of created file |
---|---|---|
regular | no | arcinfo meteo_on_equidistant_grid |
rectangular | yes | curvi meteo_on_curvilinear_grid |
curvilinear | yes | curvi meteo_on_curvilinear_grid |
...
to update should be in the workDir specified in the netcdf run file. This program only supports:
a single mdu file with file name format <model_id>.mdu or
Valid example: gtsm.mdu(in case of domain decomposition) one mdu file for each partition with file name format <model_id>_<partition_number>.mdu
Valid example: gtsm_0000.mdu, gtsm_0001.mdu, gtsm_0002.mdu
Restart file name format
In case of a warm state start, there should be exactly one input state file (restart file) for each mdu file. This program only supports a single input state file with file name format
- <model_id>_rst.nc , or
Valid example: gtsm_rst.nc - <model_id>_<timestamp>_rst.nc
Valid example: gtsm_20160407_140000_rst.nc
In case of domain decomposition there should be one input state file for each partition with file name format
<model_id>_<partition_number>_rst.nc, or
Valid example: gtsm_0001_rst.nc<model_id>_<partition_number>_<timestamp>_rst.nc
Valid example: gtsm_0001_20160407_140000_rst.nc
pre-adapter activities: Unpdate external forcing files (optional)
The pre-adapter (version Delft-FEWS 2017.01.01 and upwards) converts exported scalar timeseries from xml to external forcing files (i.e. .bc and .tim files). Please note the following:
- The pre-adapter reads the .ext files mentioned in the .mdu file, and finds here the files to check for keywords
- See Delft3D adapter with NetCDF run file#Templatefilesandkeywords on how to use template files and keywords.
- The pre-adapter can handle at most two different forcing files, so if you list more in the .mdu file they will be ignored.
- The pre-adapter assumes a timestep in minutes. Originally, the .tim files could only handle minutes. The newer .bc files can use any unit, but the pre-adapter still assumes minutes. The pre-adapter does -not- interpret the Tunit as described in the .mdu file (Implementing this would be an improvement of the pre-adapter.)
- Example config files can be found elsewhere on this wiki page
pre-adapter activities: Convert input grid time series (optional)
The netcdf file(s) specified in the property "input_grid_files_to_convert" will be converted to files in arcinfo/curvi format. Each netcdf file will be converted to a file with the same path and name as the netcdf file but with a different extension (.amu, .amv or .amp). If the property "input_grid_files_to_convert" is not specified, then this step does nothing.
Conversion from variable to file extension
Each netcdf file should contain only one variable with grid data. A netcdf file with multiple variables with grid data results in an error. The extension of the created file depends on the name of the variable in the netcdf file. For example the original file input/x_wind.nc is converted to input/x_wind.amu
netcdf variable name | extension |
---|---|
x_wind | .amu |
y_wind | .amv |
air_pressure | .amp |
precipitation | not supported by DFlowFM (for rainfall DFlowFM can use the netcdf file directly) |
any other name | not supported by DFlowFM |
Auxiliary grid file
The format (meteo_on_equidistant_grid/meteo_on_curvilinear_grid) of each of the created files depends on whether there is an auxiliary grid file present for that file. To use an auxiliary grid file for a given netcdf file, it must have the same path and name as the netcdf file, but a different extension (.grd). If an auxiliary grid file is present, then the netcdf file will be converted to a curvi file of type meteo_on_curvilinear_grid that refers to the auxiliary grid file. Otherwise it will be converted to an arcinfo file of type meteo_on_equidistant_grid. For rectangular and curvilinear grids there must always be an auxiliary grid file present, otherwise an error is given. For regular grids no auxiliary grid file is needed.
grid type | auxiliary grid (.grd) file needed | type of created file |
---|---|---|
regular | no | arcinfo file of type meteo_on_equidistant_grid |
rectangular | yes | curvi file of type meteo_on_curvilinear_grid |
curvilinear | yes | curvi file of type meteo_on_curvilinear_grid |
Order of grid cells written
The order of the grid cell values in the arcinfo/curvi grid file created by this adapter depend on the type of grid (regular/rectangular/curvilinear). For regular grids (arcinfo meteo_on_equidistant_grid file format or curvi meteo_on_curvilinear_grid file format) the grid cells are always ordered per row from left to right, starting with the upper row of the grid. For rectangular grids (curvi meteo_on_curvilinear_grid file format) the grid cells are always ordered per row from left to right, starting with the upper row of the grid. For curvilinear grids (curvi meteo_on_curvilinear_grid file format) the grid cells are always in the same order as in the netcdf file, which depends in turn on the order of the grid cells in the corresponding grid definition in Delft-FEWS (if the file was exported from Delft-FEWS). If an auxiliary grid (.grd) file is used, then the grid cell coordinates in the .grd file must be in the same order as the grid cell values in the corresponding curvi file. The easiest way to accomplish this is to run the adapter once, then check the order of the grid cell values in the created curvi file(s), then manually make sure that the grid cell coordinates in the corresponding .grd file(s) are in the right order.
Coordinate system used
The coordinate system for the coordinates in an arcinfo meteo_on_equidistant_grid file created by this adapter depends on the coordinate system used in the netcdf file, which depends in turn on the coordinate system (geodatum) in the corresponding grid definition in Delft-FEWS (if the file was exported from Delft-FEWS). Need to manually make sure that this is the same coordinate system as the coordinate system used by the model.
D-Flow FM data in Delft-FEWS
3D data: sigma layer vs Z layer
At the moment there is no example yet of a z layer D-Flow FM model connected to Delft-FEWS. All documentation and examples below are related to sigma layer models. Z layers are supported by the model adapter though. An example of import and display of z layers in a Delft-3D model can be found at Delft3D adapter - 4.3 Import and display 3D data (z layers)
Export of 3D data in generalAdapter (z layers) - NETCDF-CF_ZLAYERS
Scalar time series at the same geo point Z but with different X,Y are considered to be a Z-layer. All available Z’s are used to create a Z-axis (layer axis) in the NetCdf file, and the time series values are written to the associated Z element. To export scalar time series as Z_layers in GA with NETCDF-CF_ZLAYERS, use option <exportZLayers>true</exportZLayers> in the exportNetcdfActivity (see config example below).
An example for float salinity(time=5, node=26, z=40);
Values of Z-axis are stored in meters. Per parameter only one Z-axis is allowed. Different parameters may have different Z-axis. Z-axis values are sorted in ascending order. The number of stations in the nc file equals to the number of unique X,Y that are available in the scalar time series. The location id’s/names associated with the first (lowest) Z are written to the nc file as station id’s/names. If there are parentLocations configured, then the IdMap can be used to write the parentLocations id’s to the nc file. By default the long_name attribute of the parameters is equal to the parameter id. This default behavior is overwritten with the configuration of a parameter description in Parameters.xml, which will be used as long_name in the nc file instead. In GA the default missing value for time series is -999. You can overwrite it in GA using <missVal>, for example <missVal>NaN</missVal>
Import of 3D data in generalAdapater (sigma layers)
In case of sigma layer data, you need to configure a locationSet linking the sigma layers (% of depth) to a layer index, see config example below. In a way, this makes the handling of sigma and z layers in Delft-FEWS similar, since both can be referred to through a layer index.
Display of 2D data for overlapping domains
A common model set-up in D-Flow FM will make use of several models for an project area. For example, you could have a large scale coarse regional model, with 1 (or more) finer model(s) zooming in on the area of interest which is (are) located within the regional model area, i.e. the model areas overlap. When you display all models in 1 gridPlot, you don't want to see the coarse grid peaking out from underneath the finer local model(s). The example in the figure has 3 different model areas, going from coarse (blue grid), through intermediate (red grid) to a fine resolution (green grid).
In order to hide the coarser grids where a finer grid is available, you'll need to define a shapefile which masks the area of each model domain that you would like visualised in the gridDisplay. These shapefiles should (barely) overlap, see example in the figure on the right. All data is still available in the gridPlot, but only the data within the shapefile contour is displayed in the gridDisplay. When the user double-clicks in the gridDisplay, a timeSeriesDisplay with scalar data for all models with data for that location (in this example up to 3) is displayed, even though the data might be masked in the gridDisplay. Config example below.
Display of 3D data (sigma layers)
In GridDisplay.xml you need to configure an additional sigmaScaleReferenceTimeSeriesSet for sigma layers (see config example below). A on the fly transformation allows the user to dynamically interpolate between sigma layers in the grid display. For more information on the GridDisplay visit 01 Grid Display - sigmaScaleReferenceTimeSeriesSet
System requirements
- This program needs Java version 8 or higher.
- This program needs the following Java libraries:
- commons-httpclient-3.0.1.jar
- Delft_Util.jar (revision 60330)
- grib-8.0.jar
- log4j-1.2.14.jar
- netcdf-4.2.jar
- slf4j-api-1.5.6.jar
- slf4j-log4j12-1.5.6.jar
- TimeSeriesImport.jar (revision 60330)
Configuration example
Please note that for running DFlow-FM from Delft-FEWS only a pre-adapter is needed (a post-adapter is not needed).
Update external forcing files
Example of changes to the config when dealing with a D-Flow FM model with scalar boundary conditions.
Excerpt from .mdu file related to external forcing
Code Block | ||
---|---|---|
| ||
[external forcing]
ExtForceFileNew = mackay_bnd.ext # ExtForceFileNew DDB uses new format
ExtForceFile = mackay_pioneer.ext # *.ext
|
Example .ext file with reference to .bc file:
Code Block | ||
---|---|---|
| ||
[boundary]
quantity = waterlevelbnd
locationfile = mackay_bnd.pli
forcingfile = mackay_bnd.bc
|
With corresponing .pli file:
Code Block | ||
---|---|---|
| ||
mackay_bnd
1 2
1.49201410e+02 -2.10467553e+01 mackay_bnd_0001
|
and corresponding .bc file:
Code Block | ||
---|---|---|
| ||
[forcing]
Name = mackay_bnd_0001
Function = timeseries
Time-interpolation = linear
Quantity = time
Unit = minutes since 2017-01-01 00:00:00
Quantity = waterlevelbnd
Unit = m
$(FLOW_TIMESERIES: waterlevelbnd/mackay_bnd_0001)
|
Example .ext file with .tim file:
Code Block | ||
---|---|---|
| ||
QUANTITY=discharge_salinity_temperature_sorsin
FILENAME=mackay_pioneer.pli
FILETYPE=9
METHOD=1
OPERAND=O
AREA=1
|
With corresponding .pli file:
Code Block | ||
---|---|---|
| ||
pioneer
1 2
1.49099320e+02 -2.11482830e+01
|
and corresponding .tim file:
Code Block | ||
---|---|---|
| ||
$(FLOW_TIMESERIES: Q_sim_fcst/pioneer)
|
Example of exportTimeSeriesActivity in General Adapter config file:
Code Block | ||
---|---|---|
| ||
<exportTimeSeriesActivity>
<exportFile>timeseries.xml</exportFile>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceSetId>URBS_Forecast</moduleInstanceSetId>
<valueType>scalar</valueType>
<parameterId>Q.sim.fcst</parameterId>
<locationSetId>DFLOWFM_river.$CATCHMENT$_$SUBCATCHMENT$</locationSetId>
<timeSeriesType>simulated forecasting</timeSeriesType>
<timeStep unit="minute" multiplier="15"/>
<relativeViewPeriod unit="day" start="0" end="3"/>
<readWriteMode>read only</readWriteMode>
</timeSeriesSet>
<timeSeriesSet>
<moduleInstanceId>ImportROMS</moduleInstanceId>
<valueType>scalar</valueType>
<parameterId>H.tidal.fcst</parameterId>
<locationSetId>DFLOWFM_coastal.$CATCHMENT$_$SUBCATCHMENT$</locationSetId>
<timeSeriesType>external forecasting</timeSeriesType>
<timeStep unit="minute" multiplier="30"/>
<readWriteMode>read complete forecast</readWriteMode>
</timeSeriesSet>
</timeSeriesSets>
</exportTimeSeriesActivity>
|
D-Flow FM model configuration example (single domain, 2D data import)
Example of a FEWS general adapter configuration that uses the DFlow-FM adapter.
Code Block | ||
---|---|---|
| ||
<?xml version="1.0" encoding="UTF-8"?>
<generalAdapterRun xmlns="http://www.wldelft.nl/fews" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.wldelft.nl/fews http://fews.wldelft.nl/schemas/version1.0/generalAdapterRun.xsd">
<general>
<rootDir>$REGION_HOME$\Modules\dflowfm</rootDir>
<workDir>%ROOT_DIR%</workDir>
<exportDir>%ROOT_DIR%\dflowfm_curacao\input</exportDir>
<exportDataSetDir>$REGION_HOME$\Modules</exportDataSetDir>
<exportIdMap>IdExport_DFlowFM</exportIdMap>
<importDir>%ROOT_DIR%\dflowfm_curacao\output</importDir>
<importIdMap>IdImport_DFlowFM</importIdMap>
<dumpFileDir>$GA_DUMPFILEDIR$</dumpFileDir>
<dumpDir>%ROOT_DIR%\dflowfm_curacao\dump</dumpDir>
<diagnosticFile>%ROOT_DIR%\dummy.xml</diagnosticFile>
<missVal>-999.</missVal>
<!-- Take care this should be the timezone the computer is running in -->
<timeZone>
<timeZoneOffset>-04:00</timeZoneOffset>
</timeZone>
<endDateTimeFormat>yyyyMMdd_HHmmss</endDateTimeFormat>
</general>
<activities>
<startUpActivities>
<purgeActivity>
<filter>%ROOT_DIR%\dflowfm_curacao\output\*.*</filter>
</purgeActivity>
<purgeActivity>
<filter>%ROOT_DIR%\dflowfm_curacao\input\*.*</filter>
</purgeActivity>
</startUpActivities>
<exportActivities>
<exportStateActivity>
<moduleInstanceId>DFlowFM_curacao_Historical</moduleInstanceId>
<stateExportDir>%ROOT_DIR%\dflowfm_curacao\instate</stateExportDir>
<stateSelection>
<warmState>
<stateSearchPeriod unit="hour" start="-23" end="-2"/>
</warmState>
</stateSelection>
</exportStateActivity>
<exportNetcdfActivity>
<exportFile>air_pressure.nc</exportFile>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceId>WFLOW_curacao_GA_Historical</moduleInstanceId>
<valueType>grid</valueType>
<parameterId>P.specific</parameterId>
<locationId>wflow_curacao</locationId>
<timeSeriesType>simulated historical</timeSeriesType>
<timeStep unit="hour" multiplier="1"/>
<relativeViewPeriod unit="hour" end="0"/>
<readWriteMode>add originals</readWriteMode>
</timeSeriesSet>
</timeSeriesSets>
</exportNetcdfActivity>
<exportNetcdfRunFileActivity>
<description>This run file is passed as argument to DFLOWFM pre adapter</description>
<exportFile>%WORK_DIR%\run_info.nc</exportFile>
<properties>
<string key="model_id" value="dflowfm_curacao\curacao"/>
<string key="input_grid_files_to_convert" value="%ROOT_DIR%\dflowfm_curacao\input\x_wind.nc;%ROOT_DIR%\dflowfm_curacao\input\air_pressure.nc"/>
</properties>
</exportNetcdfRunFileActivity>
</exportActivities>
<executeActivities>
<executeActivity>
<description>DFlowFM pre adapter</description>
<command>
<className>nl.deltares.dflowfm.DFlowFMPreAdapter</className>
<binDir>adapter</binDir>
</command>
<arguments>
<argument>%WORK_DIR%\run_info.nc</argument>
</arguments>
<logFile>
<file>%WORK_DIR%\dflowfm_pre_adapter_log.txt</file>
<errorLinePattern>*ERROR*</errorLinePattern>
<warningLinePattern>*WARN*</warningLinePattern>
<infoLinePattern>*INFO*</infoLinePattern>
<debugLinePattern>*DEBUG*</debugLinePattern>
</logFile>
<timeOut>99999999</timeOut>
<ignoreDiagnostics>true</ignoreDiagnostics>
</executeActivity>
<executeActivity>
<description>Run DFLOWFM</description>
<command>
<executable>bin\unstruc.exe</executable>
</command>
<arguments>
<argument>--autostartstop</argument>
<argument>dflowfm_curacao\curacao.mdu</argument>
</arguments>
<logFile>
<file>%WORK_DIR%\dflowfm_curacao\curacao.dia</file>
<errorLinePattern>*ERROR*</errorLinePattern>
<warningLinePattern>*WARNING*</warningLinePattern>
<debugLinePattern>*INFO*</debugLinePattern>
<debugLinePattern>*DEBUG*</debugLinePattern>
</logFile>
<timeOut>44200000</timeOut>
<ignoreDiagnostics>true</ignoreDiagnostics>
</executeActivity>
</executeActivities>
<importActivities>
<importStateActivity>
<stateFile>
<importFile>%WORK_DIR%\dflowfm_curacao\output\curacao_%END_DATE_TIME%_rst.nc</importFile>
<relativeExportFile>curacao_%END_DATE_TIME%_rst.nc</relativeExportFile>
</stateFile>
</importStateActivity>
<importNetcdfActivity>
<importFile>%WORK_DIR%\dflowfm_curacao\output\curacao_map.nc</importFile>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceId>DFlowFM_curacao_Historical</moduleInstanceId>
<valueType>grid</valueType>
<parameterId>H.sim</parameterId>
<locationId>DFlowFM_Curacao</locationId>
<timeSeriesType>simulated historical</timeSeriesType>
<timeStep unit="nonequidistant"/>
<readWriteMode>add originals</readWriteMode>
</timeSeriesSet>
</timeSeriesSets>
</importNetcdfActivity>
</importActivities>
</activities>
</generalAdapterRun>
|
Z layers - export D-Flow FM 3D results (NETCDF-CF_ZLAYERS)
Code Block | ||
---|---|---|
| ||
<activities>
<exportActivities>
<exportNetcdfActivity>
<exportFile>hycom_boundary.nc</exportFile>
<exportZLayers>true</exportZLayers>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceId>Interpolate_Boundaries_HYCOM_forecast</moduleInstanceId>
<valueType>scalar</valueType>
<parameterId>S.simulated</parameterId>
<locationSetId>HYCOM.Boundaries_AllLayers</locationSetId>
<timeSeriesType>simulated forecasting</timeSeriesType>
<timeStep unit="hour" multiplier="3"/>
<relativeViewPeriod unit="day" start="0" end="1" endOverrulable="true"/>
<readWriteMode>read only</readWriteMode>
</timeSeriesSet>
</timeSeriesSets>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceId>Interpolate_Boundaries_HYCOM_forecast</moduleInstanceId>
<valueType>scalar</valueType>
<parameterId>T.simulated</parameterId>
<locationSetId>HYCOM.Boundaries_AllLayers</locationSetId>
<timeSeriesType>simulated forecasting</timeSeriesType>
<timeStep unit="hour" multiplier="3"/>
<relativeViewPeriod unit="day" start="0" end="1" endOverrulable="true"/>
<readWriteMode>read only</readWriteMode>
</timeSeriesSet>
</timeSeriesSets>
</exportNetcdfActivity>
</exportActivities>
</activities>
|
Sigma layers - import D-Flow FM 3D results
Example of changes to the config when dealing with a D-Flow FM model with multiple domains, using sigma layers.
Code Block | ||
---|---|---|
| ||
<irregular locationId="sigma_0000">
<netcdfFile>
<file>$TEMP_DIR$/3d_flowgeom_0000.nc</file>
<meshTopologyVariableName>mesh2d</meshTopologyVariableName>
<staggerLocation>face</staggerLocation>
</netcdfFile>
</irregular>
|
Code Block | ||
---|---|---|
| ||
<location id="sigma.0000">
<x>0</x>
<y>0</y>
</location>
|
Code Block | ||
---|---|---|
| ||
<locationSet id="sigmaLayers_0000"> <!-- i.e. locationSet for all sigmalayers in domain 0000 -->
<csvFile>
<file>sigma_layers.csv</file>
<id>SigmaLayer_%INDEX%_0000</id> <!-- i.e. locationId consists of SigmaLayer_0_0000, SigmaLayer_1_0000, etc for all indices / sigma layers in domain 0000 -->
<parentLocationId>sigma.0000</parentLocationId> <!-- parentLocationId, through which all sigmaLayers / locations in this set can be resolved, see for example the GridDisplay (see example below) -->
<x>0</x>
<y>0</y>
<layerSigmaCoordinate>%SIGMA%</layerSigmaCoordinate>
</csvFile>
</locationSet>
|
Code Block | ||
---|---|---|
| ||
INDEX,SIGMA
0,0.025
1,0.075
2,0.125
3,0.175
4,0.225
5,0.275
6,0.325
7,0.375
8,0.425
9,0.475
10,0.525
11,0.575
12,0.625
13,0.675
14,0.725
15,0.775
16,0.825
17,0.875
18,0.925
19,0.975
|
Through the use of <mapLocationsByLayerSigmaCoordinate> the location is resolved by the sigma layer coordinates in the generalAdapter:
Code Block | ||
---|---|---|
| ||
<?xml version="1.0" encoding="UTF-8"?>
<generalAdapterRun xmlns="http://www.wldelft.nl/fews" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.wldelft.nl/fews http://fews.wldelft.nl/schemas/version1.0/generalAdapterRun.xsd">
<general>
<rootDir>$TEMP_DIR$</rootDir>
<workDir>$TEMP_DIR$</workDir>
<exportDir>$TEMP_DIR$</exportDir>
<importDir>$TEMP_DIR$</importDir>
<dumpFileDir>$TEMP_DIR$</dumpFileDir>
<dumpDir>$TEMP_DIR$</dumpDir>
<diagnosticFile>$TEMP_DIR$/diagnostic.xml</diagnosticFile>
</general>
<activities>
<importActivities>
<importNetcdfActivity>
<importFile>%WORK_DIR%/DFM_OUTPUT/model_0000_map.nc</importFile>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceId>model_DFlowFM_FC</moduleInstanceId>
<valueType>grid</valueType>
<parameterId>H.simulated</parameterId>
<locationId>sigmaLayers.0000</locationId> <!-- parentLocation for domain 0000 -->
<timeSeriesType>simulated forecasting</timeSeriesType>
<timeStep unit="nonequidistant"/>
<readWriteMode>add originals</readWriteMode>
<expiryTime unit="day" multiplier="$EXPIRY_DAYS_SIMULATED_FORECAST_GRID$"/>
</timeSeriesSet>
<timeSeriesSet>
<moduleInstanceId>model_DFlowFM_FC</moduleInstanceId>
<valueType>grid</valueType>
<parameterId>T.simulated.v</parameterId>
<locationSetId>sigmaLayers_0000</locationSetId> <!-- locationSet off all sigmaLayers linked to above used parentLocation -->
<timeSeriesType>simulated forecasting</timeSeriesType>
<timeStep unit="nonequidistant"/>
<readWriteMode>add originals</readWriteMode>
<expiryTime unit="day" multiplier="$EXPIRY_DAYS_SIMULATED_FORECAST_GRID$"/>
</timeSeriesSet>
</timeSeriesSets>
<mapLocationsByLayerSigmaCoordinate>true</mapLocationsByLayerSigmaCoordinate>
</importNetcdfActivity>
<importNetcdfActivity> <!-- repeat for output files of all domains -->
<importFile>%WORK_DIR%/DFM_OUTPUT/model_0001_map.nc</importFile>
<timeSeriesSets>
<timeSeriesSet>
<moduleInstanceId>model_DFlowFM_FC</moduleInstanceId>
<valueType>grid</valueType>
<parameterId>H.simulated</parameterId>
<locationId>sigmaLayers.0001</locationId>
<timeSeriesType>simulated forecasting</timeSeriesType>
<timeStep unit="nonequidistant"/>
<readWriteMode>add originals</readWriteMode>
<expiryTime unit="day" multiplier="$EXPIRY_DAYS_SIMULATED_FORECAST_GRID$"/>
</timeSeriesSet>
...
</timeSeriesSets>
<mapLocationsByLayerSigmaCoordinate>true</mapLocationsByLayerSigmaCoordinate>
</importNetcdfActivity>
</importActivities>
</activities>
</generalAdapterRun>
|
Sigma layers - display D-Flow FM 3D results in GridDisplay
This example builds on the grid, location and locationSet defined in the example above. It assumes sigma layers for a multi domain model.
Code Block | ||
---|---|---|
| ||
<locationSet id="SigmaLayer_0_####"> <!-- SigmaLayer with index 0 for all domains -->
<locationId>SigmaLayer_0_0000</locationId>
<locationId>SigmaLayer_0_0001</locationId>
<locationId>SigmaLayer_0_0002</locationId>
...
</locationSet>
<locationSet id="sigma.merged"> <!-- parentLocations for all domains -->
<locationId>sigma.0000</locationId> <!-- parentLocationId for domain 0000 -->
<locationId>sigma.0001</locationId>
<locationId>sigma.0002</locationId>
...
</locationSet> |
Code Block | ||
---|---|---|
| ||
<gridDisplay xmlns="http://www.wldelft.nl/fews" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.wldelft.nl/fews http://fews.wldelft.nl/schemas/version1.0/gridDisplay.xsd">
<title>title</title>
<gridPlotGroup id="gridPlotGroupId" name="gridPlotGroupName">
<gridPlot id="gridPlotId" name="gridPlotName">
<dataLayer>
<uTimeSeriesSet>
<moduleInstanceId>DFlowFM_HC</moduleInstanceId>
|
...
System requirements
- This program needs Java version 1.7 or higher.
- This program needs the following Java libraries:
- commons-httpclient-3.0.1.jar
- Delft_FEWS.jar
- Delft_FEWS_DataStore.jar
- Delft_Util.jar
- log4j-1.2.14.jar
- netcdf-4.2.jar
- slf4j-api-1.5.6.jar
- slf4j-log4j12-1.5.6.jar
- TimeSeriesImport.jar
Configuration example
Please note that for running DFlow-FM from Delft-FEWS only a pre-adapter is needed (a post-adapter is not needed). Example of a FEWS general adapter configuration that uses the DFlow-FM adapter:
Code Block | ||
---|---|---|
xml | xml | <?xml version="1.0" encoding="UTF-8"?> <generalAdapterRun xmlns="http://www.wldelft.nl/fews" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.wldelft.nl/fews http://fews.wldelft.nl/schemas/version1.0/generalAdapterRun.xsd"> <general> <rootDir>$REGION_HOME$\Modules\dflowfm</rootDir> <workDir>%ROOT_DIR%</workDir> <exportDir>%ROOT_DIR%\dflowfm_curacao\input</exportDir> <exportDataSetDir>$REGION_HOME$\Modules</exportDataSetDir> <exportIdMap>IdExport_DFlowFM</exportIdMap> <importDir>%ROOT_DIR%\dflowfm_curacao\output</importDir> <importIdMap>IdImport_DFlowFM</importIdMap> <dumpFileDir>$GA_DUMPFILEDIR$</dumpFileDir> <dumpDir>%ROOT_DIR%\dflowfm_curacao\dump</dumpDir> <diagnosticFile>%ROOT_DIR%\dummy.xml</diagnosticFile> <missVal>-999.</missVal> <!-- Take care this should be the timezone the computer is running in --> <timeZone> <timeZoneOffset>-04:00</timeZoneOffset> </timeZone> <endDateTimeFormat>yyyyMMdd_HHmmss</endDateTimeFormat> </general> <activities> <startUpActivities> <purgeActivity> <filter>%ROOT_DIR%\dflowfm_curacao\output\*.*</filter> </purgeActivity> <purgeActivity> <filter>%ROOT_DIR%\dflowfm_curacao\input\*.*</filter> </purgeActivity> </startUpActivities> <exportActivities> <exportStateActivity> <moduleInstanceId>DFlowFM_curacao_Historical</moduleInstanceId> <stateExportDir>%ROOT_DIR%\dflowfm_curacao\instate</stateExportDir> <stateSelection> <warmState> <stateSearchPeriod unit="hour" start="-23" end="-2"/> </warmState> </stateSelection> </exportStateActivity> <exportNetcdfActivity> <exportFile>air_pressure.nc</exportFile> <timeSeriesSets> <timeSeriesSet> <moduleInstanceId>WFLOW_curacao_GA_Historical</moduleInstanceId> <valueType>grid</valueType> <parameterId>P.specific<<parameterId>parameter</parameterId> <locationId>wflow_curacao</locationId> <locationSetId>SigmaLayer_0_####</locationSetId> <!-- Configure only the top layer (index = 0). The sibling locations (i.e. other sigma layers) are resolved through the parent of the top layer. --> <timeSeriesType>simulated historical</timeSeriesType> <timeStep unit="hour" multiplier="1nonequidistant"/> <readWriteMode>read complete forecast</readWriteMode> <relativeViewPeriod unit="hour" end="0"/></uTimeSeriesSet> <vTimeSeriesSet> <readWriteMode>add originals</readWriteMode> <moduleInstanceId>DFlowFM_HC</moduleInstanceId> <valueType>grid</valueType> <<parameterId>parameter</timeSeriesSet>parameterId> </timeSeriesSets> </exportNetcdfActivity> <exportNetcdfRunFileActivity> <description>This run file is passed as argument to DFLOWFM pre adapter</description> <exportFile>%WORK_DIR%\run_info.nc</exportFile> <properties> <string key="mdu_file" value="dflowfm_curacao\curacao.mdu"/> <string key="input_grid_files_to_convert" value="%ROOT_DIR%\dflowfm_curacao\input\x_wind.nc;%ROOT_DIR%\dflowfm_curacao\input\air_pressure.nc <locationSetId>SigmaLayer_0_####</locationSetId> <!-- Configure only the top layer (index = 0). The sibling locations (i.e. other sigma layers) are resolved through the parent of the top layer. --> <timeSeriesType>simulated historical</timeSeriesType> <timeStep unit="nonequidistant"/> </properties><readWriteMode>read complete forecast</readWriteMode> </exportNetcdfRunFileActivity> </exportActivities> <executeActivities> <executeActivity>vTimeSeriesSet> <sigmaScaleReferenceTimeSeriesSet> <!-- when this is configured, a vertical slider becomes automatically visible in GridDisplay to slide through the water column --> <moduleInstanceId>DFlowFM_HC</moduleInstanceId> <description>DFlowFM pre adapter</description><valueType>grid</valueType> <command><parameterId>parameter</parameterId> <className>nl.deltares.dflowfm.DFlowFMPreAdapter</className> <binDir>adapter</binDir><locationSetId>sigma.merged</locationSetId> <!-- parentLocations for all domains, linking to all sigma layers --> <<timeSeriesType>simulated historical</command>timeSeriesType> <arguments><timeStep unit="nonequidistant"/> <argument>%WORK_DIR%\run_info.nc</argument> <readWriteMode>read complete forecast</readWriteMode> </sigmaScaleReferenceTimeSeriesSet> </arguments>dataLayer> <verticalSliderRange start="0" end="100"/> <logFile> <file>%WORK_DIR%\dflowfm_pre_adapter_log.txt</file><!-- limit the min and max water depth used in the vertical slider in the GridDisplay --> <errorLinePattern>*ERROR*</errorLinePattern> <warningLinePattern>*WARN*</warningLinePattern> <infoLinePattern>*INFO*</infoLinePattern> <debugLinePattern>*DEBUG*</debugLinePattern> </logFile> <timeOut>99999999</timeOut> <ignoreDiagnostics>true</ignoreDiagnostics> </executeActivity> <executeActivity> <description>Run DFLOWFM</description> <command> <executable>bin\unstruc.exe</executable> </command> <arguments> <argument>--autostartstop</argument> <argument>dflowfm_curacao\curacao.mdu</argument> </arguments> <logFile> <file>%WORK_DIR%\dflowfm_curacao\curacao.dia</file> <errorLinePattern>*ERROR*</errorLinePattern> <warningLinePattern>*WARNING*</warningLinePattern> <debugLinePattern>*INFO*</debugLinePattern> <debugLinePattern>*DEBUG*</debugLinePattern> </logFile> <timeOut>44200000</timeOut> <ignoreDiagnostics>true</ignoreDiagnostics> </executeActivity> </executeActivities> <importActivities> <importStateActivity> <stateFile> <importFile>%WORK_DIR%\dflowfm_curacao\output\curacao_%END_DATE_TIME%_rst.nc</importFile> <relativeExportFile>curacao_%END_DATE_TIME%_rst.nc</relativeExportFile> </stateFile> </importStateActivity> <importNetcdfActivity> <importFile>%WORK_DIR%\dflowfm_curacao\output\curacao_map.nc</importFile> <timeSeriesSets> <timeSeriesSet> <moduleInstanceId>DFlowFM_curacao_Historical</moduleInstanceId> <valueType>grid</valueType> <parameterId>H.sim</parameterId> <locationId>DFlowFM_Curacao</locationId> <timeSeriesType>simulated historical</timeSeriesType> <timeStep unit="nonequidistant"/> <readWriteMode>add originals</readWriteMode> </timeSeriesSet> </timeSeriesSets> </importNetcdfActivity> </importActivities> </activities> </generalAdapterRun> <!-- if not configured the range of slider is automatically set to cover all available water depths in the grid for the entire period displayed --> </gridPlot> </gridPlotGroup> |
Masking - display D-Flow FM 3D results in GridDisplay (multiple overlapping models)
When you have multiple overlapping models and you want to control which data is displayed in the gridDisplay, you can make use of a masking shapefile. Link this file to a locationSet. The <id> specified in the <esriShapeFile> config can be used in the GridDisplay, which will mask the data shown. For more information see above Display of 2D data for overlapping domains
Code Block | ||
---|---|---|
| ||
<locationSet id="wave_clipper.shp">
<esriShapeFile>
<file>wave_clipper.shp</file>
<id>Wave</id>
<x>0</x>
<y>0</y>
</esriShapeFile>
</locationSet> |
Code Block | ||
---|---|---|
| ||
<valueTimeSeriesSet>
<moduleInstanceId>Wave_HC</moduleInstanceId>
<valueType>grid</valueType>
<parameterId>Wave.height.simulated</parameterId>
<locationId>Wave</locationId>
<timeSeriesType>simulated historical</timeSeriesType>
<timeStep multiplier="1" unit="hour"/>
<readWriteMode>read complete forecast</readWriteMode>
</valueTimeSeriesSet> |