Test Plan
Deltares Software
Table of Contents
Table of Contents | ||
---|---|---|
|
Introduction
Deltares Systems commitment to quality control and quality assurance has leaded them to develop a formal and extensive procedure to verify the correct working of all of their geotechnical engineering tools. An extensive range of benchmark checks have been developed to check the correct functioning of each tool. During product development these checks are run on a regular basis to verify the improved product. These benchmark checks are provided in the following sections, to allow the users to overview the checking procedure and verify for themselves the correct functioning of D-FLOW SLIDE.
The benchmarks for Deltares Systems are subdivided into five separate groups as described below:
- Group 1 – Benchmarks from literature (exact solution)
Simple benchmarks for which an exact analytical result is available from literature. - Group 2 – Benchmarks from literature (approximate solution)
More complex benchmarks described in literature for which an approximate solution is known. - Group 3 – Benchmarks from spreadsheets
Benchmarks which test program features using Excel spreadsheets. - Group 4 – Benchmarks generated by the program itself
Benchmarks for which the reference results are generated using D-FLOW SLIDE. - Group 5 – Benchmarks compared with other programs
Benchmarks for which the results of D-FLOW SLIDE are compared with the results of other programs.
As much as software developers would wish they could, it is impossible to prove the correctness of any non-trivial program. Re-calculating all the benchmarks and making sure the results are as they should be will prove to some degree that the program works as it should. Nevertheless there will always be combinations of input values that will cause the program to crash or produce wrong results. Hopefully by using the verification procedure the number of times this occurs will be limited.
The benchmarks will all be described to such detail that reproduction is possible at any time. In some cases, when the geometry is too complex to describe, the input file of the benchmark is needed. The results are presented in text format with each benchmark description.
The input files belonging to the benchmarks can be downloaded from those pages.
Overview of the benchmarks
The check result (i.e. Sufficient or Insufficient) is given in blue for D-Flow Slide and in purple for the Benchmark.
Group | File name | Input file | Input file | Input file | Title | Global (VTV) | Simple (CUR-113) | Detailed (TR) | Advanced (SLIQ2D) |
---|---|---|---|---|---|---|---|---|---|
1 | bm1-1 |
|
|
| Study Case described in "Technisch Rapport Voorland Zettingsvloeiing" | Insufficient / Insufficient => |
| Sufficient / Sufficient => |
|
2 | bm2-1 |
|
|
| Spui dike - hmp 63.9 (location Nieuw Beijerland) | Insufficient / Insufficient => |
| Insufficient / Insufficient => |
|
| bm2-2 |
|
|
| Spui dike - hmp 65.0 (between locations Oud Beijerland and Nieuw Beijerland) | Sufficient / Sufficient => |
| Sufficient / Sufficient => |
|
| bm2-3 |
|
|
| Spui dike - hmp 67.8 (location Oud Beijerland) | Insufficient / Insufficient => |
| Insufficient / Sufficient => |
|
3 | bm3-1 |
|
|
| Global check with traject: step 1 = no, step 3 = yes |
|
|
|
|
| bm3-2 |
|
|
| Global check with traject: step 1 = no, step 3 = no |
|
|
|
|
| bm3-3 |
|
|
| Global check with traject: |
|
|
|
|
4 | bm4-1 |
|
|
| Test on the level indicator |
|
|
|
|
| bm4-2a |
|
|
| Test on the units (set 1) |
|
|
|
|
| bm4-2b |
|
|
| Test on the units (set 2) |
|
|
|
|
| bm4-2c |
|
|
| Test on the units (set 3) |
|
|
|
|
| bm4-2d |
|
|
| Test on the units (set 4) |
|
|
|
|
| bm4-2e |
|
|
| Test on the units (set 5) |
|
|
|
|
| bm4-2f |
|
|
| Test on the units (set 6) |
|
|
|
|
| bm4-2g |
|
|
| Test on the units (set 7) |
|
|
|
|
5 | bm5-1a |
|
|
| Comparison with SLIQ2D - Case LGZM1 |
|
|
| Insufficient / Insufficient => |
| bm5-1b |
|
|
| Comparison with SLIQ2D - Case LGZM2 |
|
|
| Insufficient / Insufficient => |
| bm5-1c |
|
|
| Comparison with SLIQ2D - Case LGZM3 |
|
|
| Insufficient / Insufficient => |
| bm5-1d |
|
|
| Comparison with SLIQ2D - Case LGZM4 |
|
|
| Insufficient / Insufficient => |
| bm5-1e |
|
|
| Comparison with SLIQ2D - Case SIMPLETA |
|
|
| Insufficient / Insufficient => |
| bm5-1f |
|
|
| Comparison with SLIQ2D - Case LG1D5N5H |
|
|
| Insufficient / Insufficient => |
| bm5-1g |
|
|
| Comparison with SLIQ2D - Case HBPZBUI3 |
|
|
| Insufficient / Insufficient => |
| bm5-2 |
|
|
| Comparison with SLIQ2D-Windows - 2 layers partially saturated with fixed slope angle |
|
| Sufficient / Sufficient => |
|
| bm5-3 |
|
|
| Comparison with DZettingsVloeiing - Study Case described in "Technisch Rapport Voorland Zettingsvloeiing" |
|
| Sufficient / Sufficient => |
|
Group 1: Benchmarks from literature (exact solution)
This section describes a number of benchmarks for which an exact analytical solution can be found in the literature.
1.1. Study Case described in "Technisch Rapport Voorland Zettingsvloeiing"
Description
The example given in "Annex A - Case Study" of the Deltares report 1200503-001-GEO-0004 "Concept Technisch Rapport Voorland Zettingsvloeiing" of G.A. van den Ham & Co is used.
In this example, both global and detailed checks are completed on the basis of a (fictitious) dike section, which with regard to geometry and soil structure is typical of the Southwest Delta.
The dike has a height of NAP+5 m, a crest width of 3 m and a slope of 1:3.
The foreshore begins to imaginary toe of the dike at an elevation of NAP and is 60 m wide. The toe of the trench is NAP-15 m and has a slope of 1:6. The dike section is 800 m long. The phreatic level is at NAP-2 m.
The soil profile is as follows:
- from NAP+3.5 m to NAP+1 m: peat
- from NAP+1 m to NAP-5 m: silty clay
- from NAP-5 m to NAP-18 m: moderately to loosely compacted sand (Calais)
- from NAP-18 m to NAP-30 m: densely compacted sand
Benchmarks results
The details of the calculation can be found in annex A of the report. The main results are given in the table below. The global check fails but the detailed check passes.
D-Flow Slide results
Results of benchmark 1-1 for the Global Check
Results | Benchmark | D-Flow Slide | Relative error % |
---|---|---|---|
Step 1 | xxx | xxx | xxx |
Group 2: Benchmarks from literature (approximate solution)
This section uses the results of a by-hand calculation performed for three profiles of the Spui dike project (see figure below):
- km 63.9 (Nieuw Beijerland)
- km 65.0 (between Oud Beijerland and Nieuw Beijerland)
- km 67.8 (Oud Beijerland)
As the details of the calculation performed by hand are not available, those benchmarks are set in group 2.
2.1. Spui dike at km 63.9 (Nieuw Beijerland)
Description
The dike profile at hmp 63.9 is given in the figure below.
The soil profile and the material properties are given in the following table:
Level top layer (m NAP) | Material | Formation | Material sensitive to liquefaction | Dr (%) | n (%) | nmin (%) | nmax (%) | Gamma unsat (kN/m3) | Gammasat (kN/m3) | Gamma grains (kN/m3) | D50 (mm) | D15 (mm) | Phi (deg) | c (kPa) | Epsvoldm0 | smax | s2 | kso (kN/m2) | m | r | u | v |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Grond level | Clay | Dunkirk / anthropogenic | No |
|
|
|
| 18 | 18 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-0.5 | Clay/Sand | Dunkirk | No |
|
|
|
| 18 | 18 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-6.5 | Peat | Holland | No |
|
|
|
| 10 | 10 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-7.5 | Clay | Calais | No |
|
|
|
| 18 | 18 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-8.5 | Sand clayey/Sand | Calais | Yes | 35 | 45 | 36.5 | 49.5 | 19 | 19 | 26.5 | 0.160 | 0.080 | 25 | 0 | 0.000444 | 1.575 | 1.2 | 43.2 | 3 | 7 | 1.2 | 1 |
-9.5 | Sand | Calais | Yes | 30 | 45.6 | 36.5 | 49.5 | 20 | 20 | 26.5 | 0.160 | 0.080 | 30 | 0 | 0.000325 | 1.55 | 1.2 | 41.6 | 3 | 7 | 1.2 | 1 |
-12.5 | Sand | Calais | Yes | 25 | 46.3 | 36.5 | 49.5 | 20 | 20 | 26.5 | 0.160 | 0.080 | 30 | 0 | 0.000238 | 1.525 | 1.2 | 40 | 3 | 7 | 1.2 | 1 |
-18 | Sand | Pleistocene | Yes | 60 | 41.7 | 36.5 | 49.5 | 20 | 20 | 26.5 | 0.160 | 0.080 | 35 | 0 | 0.00212 | 1.7 | 1.2 | 51.2 | 3 | 7 | 1.2 | 1 |
The other calculation parameters used are:
- Water level: 0.9 m
- Required probability of failure of the dike: 1:4000
- Percentage probability of failure byliquefaction: 1 %
- Model factor: 1
- Area ratio (c = A2/A1): 1.4
- Standard deviation cot(gamma): 4.6
- Considered dike length: 100 m
Benchmark results
According to the by hand calculation, both Global and Advanced checks fail.
D-FLOW SLIDE results
D-FLOW SLIDE results are in accordance with the results by hand as show in the table below.
Method | Benchmark | D-FLOW SLIDE | Relative error |
---|---|---|---|
Global check | Failed | Failed | |
Detailed check | Failed | Failed | |
2.2. Spui dike at km 65.0 (between Oud Beijerland and Nieuw Beijerland)
Description
The dike profile at km 65.0 is given in the figure below.
The soil profile and the material properties are the same as for the profile at km 63.9 (see paragraph 2.1).
Benchmark results
According to the by hand calculation, both Global and Advanced checks pass.
D-FLOW SLIDE results
D-FLOW SLIDE results are in accordance with the results by hand as show in the table below.
Method | Benchmark | D-FLOW SLIDE | Relative error |
---|---|---|---|
Global check | Passed | Passed | |
Detailed check | Passed | Passed | |
2.3. Spui dike at km 67.8 (oud Beijerland)
Description
The dike profile at km 67.8 is given in the figure below.
The soil profile and the material properties are given in the following table:
Level top layer (m NAP) | Material | Formation | Material sensitive to liquefaction | Dr (%) | n (%) | nmin (%) | nmax (%) | Gammaunsat (kN/m3) | Gammasat (kN/m3) | Gammagrains (kN/m3) | D50 (mm) | D15 (mm) | Phi (deg) | c (kPa) | Epsvoldm0 | smax | s2 | kso (kN/m2) | m | r | u | v |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Grond level | Clay | Dunkirk / anthropogenic | No |
|
|
|
| 18 | 18 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-0.5 | Clay/Sand | Dunkirk | No |
|
|
|
| 18 | 18 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-4 | Peat | Holland | No |
|
|
|
| 10 | 10 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-5 | Clay | Calais | No |
|
|
|
| 18 | 18 | 26.5 |
|
| 25 | 0 |
|
|
|
|
|
|
|
|
-6 | Sand | Calais | Yes | 20 | 46.9 | 36.5 | 49.5 | 20 | 20 | 26.5 | 0.160 | 0.080 | 30 | 0 | 0.000174 | 1.5 | 1.2 | 38.4 | 3 | 7 | 1.2 | 1 |
-20 | Sand | Pleistocene | Yes | 60 | 41.7 | 36.5 | 49.5 | 20 | 20 | 26.5 | 0.160 | 0.080 | 35 | 0 | 0.00212 | 1.7 | 1.2 | 51.2 | 3 | 7 | 1.2 | 1 |
Benchmark results
According to the by hand calculation, the Global check fails and the Advanced check passes.
D-FLOW SLIDE results
D-FLOW SLIDE results differ from the results by hand for the Detailed check, as show in the table below.
Method | Benchmark | D-FLOW SLIDE | Relative error |
---|---|---|---|
Global check | Failed | Failed | |
Detailed check | Passed | Failed | |
Group 3: Benchmarks from spreadsheets
This section contains tests that are missing in the other groups, for example for the CUR-113 method.
Group 4: Benchmarks generated by the program itself
This section contains test for which the reference results are generated with D-FLOW SLIDE.
4.1 Test on the level indicator
Description
To check that the level indicator is correctly inputted in D-FLOW SLIDE, the results of the two following calculations should lead to the same results:
- Benchmark 4-1a uses the same input as benchmark 1-1a, refer to paragraph 1.1 above.
- Benchmark 4-1b uses the same input as benchmark 4-1a except that the Y coordinates of the geometry are shifted by -20 m so that all points have a negative Y coordinate.
4.2 Test on the units
Group 5: Benchmarks compared with other programs
5.1 Comparison with SLIQ2D (DOS and Windows) - One fully saturated layer with variable slope angle
Description
The benchmarks in this paragraph are intended to verify the advanced method by comparing D-FLOW SLIDE results with those from the older program SLIQ2D, using both DOS and Windows versions of this program.
Because of the limitations in the DOS version of SLIQ2D, only one fully saturated layer is inputted. The geometry and the material properties for each cases are given in the table below.
The original slope angle is 1:1.25 and is set to "variable" so that the program will search (for each point) for the most unfavorable slope.
Benchmark name | Original file name (SLIQ2D-DOS) | Soil type | Slope height (m) | Slope angle | n (%) | nmin (%) | n max (%) | Eps voldm0 | m | r | s 2 | s max | v | k so (kN/m 2) | u | Unit weight (kN/m 3) | D r (%) |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
bm5-1a | LGZM1 | Sand clay | 21.9 | 1:1.25 | 45.5 | 50 | 35 | 0.0025 | 1.7 | 7 | 1.28 | 1.7 | 1 | 50000 | 1 | 8.856 | 30 |
bm5-1b | LGZM2 | Sand clay | 21.9 | 1:1.25 | 45.5 | 50 | 35 | 0.0035 | 1.7 | 7 | 1.28 | 1.7 | 1 | 50000 | 1 | 8.856 | 30 |
bm5-1c | LGZM3 | Sand clay | 21.9 | 1:1.25 | 45.5 | 50 | 35 | 0.005 | 1.7 | 7 | 1.28 | 1.7 | 1 | 50000 | 1 | 8.856 | 30 |
bm5-1d | LGZM4 | Sand clay | 21.9 | 1:1.25 | 45.5 | 50 | 35 | 0.006 | 1.7 | 7 | 1.28 | 1.7 | 1 | 50000 | 1 | 8.856 | 30 |
bm5-1e | SIMPLETA | Sea sand | 10 | 1:1.25 | 47.4 | 50 | 37 | 0.0092 | 3 | 7 | 1.23 | 1.35 | 1 | 39460 | 1.33 | 8.547 | 20 |
bm5-1f | LG1D5N5H | Sand clay | 20.9 | 1:1.25 | 40.2 | 50 | 35 | 0.0022 | 1.7 | 7 | 1.18 | 1.4 | 1 | 85000 | 1 | 9.717 | 65.333 |
bm5-1g | HBPZBUI3 | Sea sand | 22 | 1:1.25 | 45.5 | 50 | 35 | 0.0054 | 2 | 7 | 1.25 | 1.4 | 1.25 | 50000 | 1 | 8.856 | 30 |
Benchmark results
In SLIQ2D-Windows only the value of the tangent angle is available in the output. The other parameters (such as Ko, the normal stress p and the deviatoric stress q) are not saved and can only be red on the screen, making the comparison difficult. Nota also that the automatic generation of the variable values of the slope angle used by SLIQ2D-DOS is not exactly the same as in SLIQ2D-Windows or D-FLOW SLIDE (which use 2 extra slopes compared to SLIQ2D-DOS: 1:1.4 and 1:1.3). The figures below show the critical slope angles, for each calculated points.
Results of SLIQ2D-Windows - Overview of the unstable points:
bm5-1a: | bm5-1b: | bm5-1c: |
bm5-1d: | bm5-1e: | bm5-1f: |
bm5-1g: |
Results of SLIQ2D-Windows - Values of the critical slope angle for each calculated point:
bm5-1a: | bm5-1b: |
bm5-1c: | bm5-1d: |
bm5-1e: | bm5-1f: |
bm5-1g: |
|
D-FLOW SLIDE results
Maximum relative error between SLIQ2D-DOS and D-FLOW SLIDE:
Case | Slope angle at which instability occurs (Tan Alpha) | Tan Alpha_p | Ko_p | Normal stress p | Deviatoric stress q |
---|---|---|---|---|---|
bm5-1a | 0.00 | 0.00 | 0.00 | 0.00 | 0.00 |
bm5-1b | 0.00 | 0.00 | 0.00 | 0.00 | 0.00 |
bm5-1c | 0.00 | 0.54 | 0.13 | 0.00 | 0.00 |
bm5-1d | 0.00 | 0.00 | 0.00 | 0.00 | 0.00 |
bm5-1e | 0.00 | 0.00 | 0.15 | 0.00 | 0.02 |
bm5-1f | 0.00 | 0.00 | 0.00 | 0.00 | 0.00 |
bm5-1g | 0.00 | 0.00 | 0.12 | 0.00 | 0.02 |
Results between SLIQ2D-Windows and D-FLOW SLIDE are exactly the same for the tangent angle, as show in the table below.
Maximum relative error between SLIQ2D-Windows and D-FLOW SLIDE for the tangent angle:
Case | Tan Alpha |
---|---|
bm5-1a | 0.00 % |
bm5-1b | 0.00 % |
bm5-1c | 0.00 % |
bm5-1d | 0.00 % |
bm5-1e | 0.00 % |
bm5-1f | 0.00 % |
bm5-1g | 0.00 % |
5.2 Comparison with SLIQ2D-Windows - 2 layers partially saturated with fixed slope angle
Description
This benchmark is intended to verify the advanced method by comparing D-FLOW SLIDE results with those from the older program SLIQ2D-Windows, for a 21 m height channel composed of 2 layers where the top layer is partially saturated. The slope of the channel is fixed to 1:3.333 (i.e. Tan Alpha = 0.3).
Layer | Height (m) | Soil type | n (%) | n min (%) | n max (%) | Eps voldm0 | m | r | s 2 | s max | v | k so (kN/m 2) | u | Unit weight (kN/m 3) | D r (%) |
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Top sand | 12 | Sand clay | 45.5 | 50 | 35 | 0.006 | 1.7 | 7 | 1.28 | 1.7 | 1 | 50000 | 1 | 8.856 | 30 |
Bottom sand | 9 | Sand clay | 47.4 | 50 | 37 | 0.0092 | 3 | 5 | 1.23 | 1.35 | 1.25 | 39460 | 1.33 | 6.312 | 20 |
Benchmark results
Results of SLIQ2D-Windows for bm5-2 - Overview of the unstable points:
D-FLOW SLIDE results
Results between SLIQ2D-Windows and D-FLOW SLIDE are exactly the same for all calculated parameters, as shown in the table below.
Maximum relative error between SLIQ2D-Windows and D-FLOW SLIDE:
, including a test plan.
The Test plan document can be as varied as the products and organizations to which they apply.
This section describes how these tests will take place at three different levels:
- Code level - unit test: Program code must be tested alongside the code. Such a test checks if the code does what it is supposed to do with a little test. The tests on code level are the unit tests. For each relevant function, a unit test is defined within the C# solution. A relevant function is a function that actually performs part of the calculation, validation or I/O of the core. Properties and purely administrational functions do not have unit tests.
These tests are considered to be ok when the unit tests pass and when the code coverage of those tests is more than 75%. For these tests the following information must be provided in the Test Report:
Number of unit tests
Code coverage of the unit tests (not done)
Specify if all unit tests succeed or not
- Functional level - integration test: The tests on functional level are the integration tests. These types of tests combine multiple functions in D-Flow Slide to prove that high level functionality works. For this, a unit test is defined within the C# solution for each method with high level functionality. These tests are considered to be ok when the unit tests pass. The following information must be provided in the Test Report:
- Number of integration tests (= Benchmarks)
- Code coverage of the unit tests (not done)
- Specify if all integration tests succeed or not
...
3. Application level (System tests) : The tests on this level are to provide proof of the fact that the D-Flow Slide meets its acceptation criteria. The criteria are:
- Alle main functions must provide the correct answers (detailed results of these tests can be found in the Test Report) to confirm its performance according to the functional design.
- All possible errors must be handled and reported properly.
Based on the formulae in the Functional Design for D-Flow Slide benchmarks were created to test the kernel and the User Interface.
Test Report
The following chapters describe the tests in detail. If all tests are run with a satisfying result, the kernel is said to be good
The Userinterface has been tested manually by students using the Checklist for the program, based on the usermanual with technical requirements.
Number of Unit tests
- Deltares.FlowSlide.Data.Tests : 291 tests inclusive benchmarks (test the calculation)
- Deltares.FlowSlide.Forms.Tests : 40 tests (test the UI of D-Flow Slide)
Benchmarks - Integration tests
These benchmark (integration test, 29) checks are provided in the following sections, to allow the users to overview the checking procedure and verify for themselves the correct functioning of D-FLOW SLIDE.
The benchmarks for Deltares Systems are subdivided into five separate groups as described below:
- Group 1 – Benchmarks from literature (exact solution)
Simple benchmarks for which an exact analytical result is available from literature. - Group 2 – Benchmarks from literature (approximate solution)
More complex benchmarks described in literature for which an approximate solution is known. - Group 3 – Benchmarks from spreadsheets
Benchmarks which test program features using Excel spreadsheets. - Group 4 – Benchmarks generated by the program itself
Benchmarks for which the reference results are generated using D-FLOW SLIDE. - Group 5 – Benchmarks compared with other programs
Benchmarks for which the results of D-FLOW SLIDE are compared with the results of other programs.
As much as software developers would wish they could, it is impossible to prove the correctness of any non-trivial program. Re-calculating all the benchmarks and making sure the results are as they should be will prove to some degree that the program works as it should. Nevertheless there will always be combinations of input values that will cause the program to crash or produce wrong results. Hopefully by using the verification procedure the number of times this occurs will be limited.
The benchmarks will all be described to such detail that reproduction is possible at any time. In some cases, when the geometry is too complex to describe, the input file of the benchmark is needed. The results are presented in text format with each benchmark description.
The input files (*.fsx, *.mbr, *.slq) of all benchmarks can be downloaded here.
The test document used to check to program manually has been attached to this page.
The spreadsheets used for benchmarks in group 3 can be downloaded here.
Overview of the benchmarks
Legend:
= Results of D-Flow Slide and results of the Benchmark are identical.
= Results of D-Flow Slide and results of the Benchmark differ.
Group | Input file (*.fsx) | Title | Global | Detailed | Overall | Advanced liquefaction(SLIQ2D) | Advanced breaching |
---|---|---|---|---|---|---|---|
1 | bm1-1 | Study Case described in Technisch Rapport Voorland Zettingsvloeiing | |
|
| ||
bm1-2a | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case A | ||||||
bm1-2b | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case B | ||||||
bm1-2c | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case C | ||||||
bm1-2d | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case D | ||||||
bm1-2e | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case E | ||||||
bm1-2f | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case F | ||||||
bm1-2g | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case G | ||||||
bm1-2h | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case H | ||||||
bm1-2i | Determination of the steepest possible breaching profile (step 7 of the Global check) - Case I | ||||||
2
| bm2-1 | Spui dike - hmp 63.9 (location Nieuw Beijerland) |
|
| |||
bm2-2 | Spui dike - hmp 65.0 (between locations Oud Beijerland and Nieuw Beijerland) |
|
|
|
| ||
bm2-3 | Spui dike - hmp 67.8 (location Oud Beijerland) |
|
| ||||
3
| bm3-1a | Global check with traject: step 1 = No (Global passes) |
|
| |||
bm3-1b | Global check with traject: step 1 = Yes, step 3 = Yes (Global fails) | ||||||
bm3-1c | Global check with traject: step 1 = Yes, step 3 = No, step 4 = No (Global passes) |
|
|
| |||
bm3-1d | Global check with traject: step 1 = Yes, step 2 = No, step 4 = Yes, step 5 = Yes (Global fails) |
|
| ||||
bm3-1e | Global check with traject: step 1 = Yes, step 2 = No, step 4 = Yes, step 5 = No, step 6 = Yes (Global fails) |
|
| ||||
bm3-1f | Global check with traject: step 1 = Yes, step 2 = No, step 4 = Yes, step 5 = No, step 6 = No, step 7 = Yes (Global fails) |
|
| ||||
bm3-1g | Global check with traject: step 1 = Yes, step 2 = No, step 4 = Yes, step 5 = No, step 6 = No, step 7 = No (Global passes) | ||||||
5
| bm5-1a | Comparison with SLIQ2D-Windows - 1 saturated layer (Case LGZM1) |
|
|
| ||
bm5-1b | Comparison with SLIQ2D-Windows - 1 saturated layer (Case LGZM2) |
|
|
| |||
bm5-1c | Comparison with SLIQ2D-Windows - 1 saturated layer (Case LGZM3) |
|
|
| |||
bm5-1d | Comparison with SLIQ2D-Windows - 1 saturated layer (Case LGZM4) |
|
|
| |||
bm5-1e | Comparison with SLIQ2D-Windows - 1 saturated layer (Case SIMPLETA) |
|
|
| |||
bm5-1f | Comparison with SLIQ2D-Windows - 1 saturated layer (Case LG1D5N5H) |
|
|
| |||
bm5-1g | Comparison with SLIQ2D-Windows - 1 saturated layer (Case HBPZBUI3) |
|
|
| |||
bm5-2 | Comparison with SLIQ2D-Windows - 2 layers partially saturated |
|
|
| |||
bm5-3 | Comparison with HMBreach - 1 layer |
|
|
| |
(a) The Global and Detailed checks with D-FLOW SLIDE fail whereas according to the by hand calculation they should succeed. However, by lack of information, the input value of several parameters (state parameter, critical retrogression length and migration velocity foreshore) is set arbitrary. Therefore, this comparison is not completely relevant, and it can't be concluded that the program gives incorrect results.
(b) The overall result is not correctly determined in D-Flow Slide if the foreshore is artificial: D-Flow Slide uses the Detailed check result but it should directly conclude that the Overall check fails.
...
Parameter
...
Max. relative error (%)
...
Tan Alpha_p
...
0.00
...
Ko_p
...
0.00
...
Normal stress p
...
0.00
...
Deviatoric stress q
...