...
Link properties to data configuration elements
There are several options available:
Link Height To Data Configuration Options
Link height to data configuration elements
Optional. If specified, then for this component the height attribute is linked to the data values for the specified variable. If the data value is less than dataLowerLimit, then the height is set to heightLowerLimit. If the data value is greater than dataUpperLimit, then the height is set to heightUpperLimit. If the data value is between dataLowerLimit and dataUpperLimit, then the height will be linearly interpolated between heightLowerLimit and heightUpperLimit. If no data is available, then this component is made invisible.
Note: it is required that dataUpperLimit is greater than dataLowerLimit. However it is possible to define heightUpperLimit less than heightLowerLimit to control the direction of the change of the height.
...
The anchor point describes which part of the component should remain at the same position when the height is changed. Can be "bottom" or "top".
Link Rotation To Data Configuration Options
Link rotation to data configuration elements
Optional. If specified, then for this component the rotation is linked to the data values for the specified variable. The rotation that is derived from the data values is always relative to the rotation angle that is specified for this component in the svg file. If the data value is less than dataLowerLimit, then the rotation is set to rotationLowerLimit. If the data value is greater than dataUpperLimit, then the rotation is set to rotationUpperLimit. If the data value is between dataLowerLimit and dataUpperLimit, then the rotation will be linearly interpolated between rotationLowerLimit and rotationUpperLimit. If no data is available, then this component is made invisible. If the data value is flagged as "varying direction" (e.g. varying wind direction), then the rotation will increase linearly in time (animation). In this case the rotation will increase from rotationLowerLimit to rotationUpperLimit and then start from rotationLowerLimit again.
Note: it is required that dataUpperLimit is greater than dataLowerLimit. However it is possible to define rotationUpperLimit less than rotationLowerLimit to control the direction of the rotation. If rotationUpperLimit is greater than rotationLowerLimit, then increasing data values result in clockwise rotation.
variable
The data for this variable is used to determine the rotation for this component.
dataLowerLimit
If the data value is less than or equal to dataLowerLimit, then the rotation will be equal to rotationLowerLimit.
dataUpperLimit
If the data value is greater than or equal to dataUpperLimit, then the rotation will be equal to rotationUpperLimit.
rotationLowerLimit
The rotation (in degrees) that corresponds to the dataLowerLimit value. This rotation is always relative to the rotation angle that is specified for this component in the svg file.
rotationUpperLimit
The rotation (in degrees) that corresponds to the dataUpperLimit value. This rotation is always relative to the rotation angle that is specified for this component in the svg file.
anchorPointX
The x coordinate of the anchor point. The rotation will be around the anchor point.
anchorPointY
The y coordinate of the anchor point. The rotation will be around the anchor point.
Use Threshold Warning Level Colors Configuration Options
Use threshold warning level colors configuration elements
variable
The data for this variable is used to determine threshold crossings. For crossed thresholds, warningLevels are activated. The color of the most severe activated warningLevel is used as the fill and/or stroke color for the component, as specified below.
...
Tooltip configuration elements
variable
The data from this variable is used to replace the tags in the specified toolTip text. If for a given tag the required data is not available, then that tag is replaced by a dash symbol "-". This variable is only required if the specified toolTip text contains tags.
...
- %MAXVALUE(numberFormatId)% is replaced by the maximum reliable or doubtful value in the time series.
- %MINVALUE(numberFormatId)% is replaced by the minimum reliable or doubtful value in the time series.
- %LASTVALUE(numberFormatId)% is replaced by the most recent reliable or doubtful value in the time series.
- %LASTVALUETIME(dateFormatId)% is replaced by the date and time of the most recent reliable or doubtful value in the time series.
- %STARTTIME(dateFormatId)% is replaced by the start date and time of the relative view period of the time series.
- %ENDTIME(dateFormatId)% is replaced by the end date and time of the relative view period of the time series.
variable
The data from this variable is used to replace the tags in the text in the svg object that this component refers to. If for a given tag the required data is not available, then that tag is replaced by a dash symbol "-".
...