Group 1: Benchmarks from literature (exact solution)
This section describes a number of benchmarks for which an exact analytical solution can be found in the literature.
1.1. Study Case described in "Technisch Rapport Voorland Zettingsvloeiing"
Description
The example given in "Annex A - Case Study" of the Deltares report 1200503-001-GEO-0004 "Concept Technisch Rapport Voorland Zettingsvloeiing" of G.A. van den Ham & Co is used.
In this example, both global and detailed checks are completed on the basis of a (fictitious) dike section, which with regard to geometry and soil structure is typical of the Southwest Delta.
The dike has a height of NAP+5 m, a crest width of 3 m and a slope of 1:3.
The foreshore begins to imaginary toe of the dike at an elevation of NAP and is 60 m wide. The toe of the trench is NAP-15 m and has a slope of 1:6. The dike section is 800 m long. The phreatic level is at NAP-2 m.
The soil profile is as follows:
- from NAP+3.5 m to NAP+1 m: peat
- from NAP+1 m to NAP-5 m: silty clay
- from NAP-5 m to NAP-18 m: moderately to loosely compacted sand (Calais)
- from NAP-18 m to NAP-30 m: densely compacted sand
Benchmarks results
The details of the calculation can be found in annex A of the report. The main results are given in the table below. The global check fails but the detailed check passes.
D-Flow Slide results
Results of benchmark 1-1 for the Global Check
| Unit | Benchmark | D-FLOW SLIDE | Relative error |
---|---|---|---|---|
Marge | [m] | 35 | 35 | 0.00% |
X coordinate of the observation profile (Xsign) | [m] | -35 | -35 | 0.00% |
X coordinate of the liquefaction point (XZV) | [m] | 30 | 30 | 0.00% |
Step 1: Is liquefaction damaging on basis of geometry? |
| Yes | Yes | |
Step 2: Artificially underwater installed and non-compacted sandy foreshore? |
| No | No | |
Step 4: Is liquefaction possible on the basis of the geometry? |
| Yes | Yes | |
Step 5: Are there any sensitive to liquefaction layers present? |
| Yes | Yes | |
Result of the Global Check |
| Failed | Failed |
Results of benchmark 1-1 for the Detailed Check
| Unit | Benchmark | D-FLOW SLIDE | Relative error |
---|---|---|---|---|
Fictive channel depht (Hr) | [m] | 21.571 | 21.571 | 0.00 % |
Fictive slope (cotan αr) | [-] | 10.500 | 10.500 | 0.00 % |
Probability of liquefaction | [-] | 2.93 × 1E-03 | 2.93 × 1E-03 | 0.00 % |
Representative probability of failure | [-] | 3.52 × 1E-03 | 3.52 × 1E-03 | 0.00 % |
β | [-] | 3.749 | 3.749 | 0.00 % |
P(L > Lallowable) | [-] | 8.87 × 1E-05 | 8.86 × 1E-05 | 0.08 % |
Probability of failure | [-] | 3.12 × 1E-07 | 3.12 × 1E-07 | 0.00 % |
Allowable probability of failure | [-] | 2.50 × 1E-06 | 2.50 × 1E-06 | 0.00 % |
Result of Detailed Check |
| Succeeded | Succeeded |